MAXSA 44311 Assembly & Operating Instructions

Solar-powered led security spotlight

Advertisement

Quick Links

solar-powered
LED SECURITY SPOTLIGHT
ASSEMBLY & OPERATING INSTRUCTIONS

ABOUT YOUR SOLAR POWERED LED SECURITY SPOTLIGHT

During the day, the solar panel included with this MAXSA Solar Security Spotlight converts sunlight into
electricity, recharging the pre-installed batteries. Using this stored energy, the two, super-bright LEDs turn
on automatically at night when motion is detected. These LEDs have an estimated life of 30,000 hours so
they should not need to be changed.
This Solar Powered LED Security Spotlight has an adjustable TIME dial that allows light duration of up to 60
seconds. When the batteries are fully charged, this Solar Security Light can light up for up to 120 minutes,
which is equivalent to 120 one-minute cycles when the TIME dial is set to the maximum (+) position.
The Solar Powered LED Security Spotlight has a built-in motion sensor, which automatically turns on the
light when movement of a heat source (such as people, animals, or cars) is detected in the area. The light
remains on while motion continues to be detected in the area.
The Solar Powered LED Security Spotlight has a LUX setting which can be adjusted to control the functioning
of the built-in photosensor so that the light only turns on at night.
The batteries included in this unit are 3 AA rechargeable batteries and will need to be replaced when the
charging ability is decreased. The batteries should last for approximately 3 years before they will need to be
replaced. The shorter the time period used, the longer the battery will last. The Solar Powered LED Security
Spotlight may function irregularly or not at all at temperatures near or below freezing (32˚ F/0˚ C) due to
the functionality of Ni-MH rechargeable batteries. Normal operation will return when the temperature rises.
Model #: 44311

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 44311 and is the answer not in the manual?

Questions and answers

Summary of Contents for MAXSA 44311

  • Page 1 ASSEMBLY & OPERATING INSTRUCTIONS ABOUT YOUR SOLAR POWERED LED SECURITY SPOTLIGHT During the day, the solar panel included with this MAXSA Solar Security Spotlight converts sunlight into electricity, recharging the pre-installed batteries. Using this stored energy, the two, super-bright LEDs turn on automatically at night when motion is detected.
  • Page 2 INCLUDED PARTS: Carefully remove and identify all the parts from their protective packaging and lay them out in front of you. 2 screws and anchors for mounting solar panel 3 screws and anchors for mounting solar panel Adjustment dials are located on the underside of the main body. They are denoted by TIME and LUX stamps. CHOOSING A LOCATION FOR YOUR SOLAR SECURITY LIGHT: This Solar Security Light comes complete with a solar panel attached to a 10 foot power cord.
  • Page 3 TO INSTALL THE MOUNTING BRACKET Remove the mounting bracket from the back of the light. Align the mounting bracket on the wall and mark the locations of the two holes to be drilled with a pencil. Remove the mounting bracket from the wall. Drill pilot holes for screws if needed.
  • Page 4 OPERATING YOUR SOLAR SECURITY LIGHT After the initial 3 day charge of your Solar Security Light, move the switch on the main body to the ON position. Your Solar Security Light is now ready for use. Underneath the motion sensor, there are 2 adjustment dials: TIME and LUX. The light has been factory preset as follows: TIME - Set at 30 seconds.
  • Page 5 • Test the motion sensor by covering it completely with cardboard and waiting several minutes to make sure it does not detect motion. If the light still switches on, please contact MAXSA for further assistance. • Battery charge may be low. Turn the power switch to the OFF position and charge the batteries for three (3) sunny days with the solar panel placed in direct sunlight.
  • Page 6 (consumer pays return shipping) to MAXSA Innovations, LLC, 8412 Cathedral Forest Dr; Fairfax Station, VA 22039; USA within the warranty period, and if the product is defective, MAXSA Innovations, LLC will at its option repair or replace such. This warranty shall constitute the sole liability of MAXSA Innovations, LLC concerning the product. MAXSA Innovations, LLC expressly disclaims all other warranties INCLUDING, WITHOUT LIMITATION, THE WARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Table of Contents