Kremlin 12.22 Instruction Manual

Extrusion pump

Advertisement

Quick Links

INSTRUCTION MANUAL
EXTRUSION PUMP - MODEL 12.22
Notice : 0501 573.049.110
Date : 3/01/05 - Supersede : 7/06/04 - Modif. Up to date
KREMLIN REXSON - 150, avenue de Stalingrad – 93 245 – STAINS Cédex - FRANCE
Téléphone : 33 (0)1 49 40 25 25
Fax : 33 (0)1 48 26 07 16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 12.22 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Kremlin 12.22

  • Page 1 Notice : 0501 573.049.110 Date : 3/01/05 - Supersede : 7/06/04 - Modif. Up to date KREMLIN REXSON - 150, avenue de Stalingrad – 93 245 – STAINS Cédex - FRANCE Téléphone : 33 (0)1 49 40 25 25 Fax : 33 (0)1 48 26 07 16...
  • Page 2: Table Of Contents

    INSTRUCTION MANUAL WAX PUMP - MODEL 12.22 SUMMARY EC DECLARATION OF CONFORMITY...................... 2 GENERAL SAFETY INSTRUCTIONS ......................2 TECHNICAL FEATURES ..........................3 INSTALLATION ............................4 OPERATING PRINCIPLE..........................5 START UP..............................6 SHUTDOWN AT END OF WORK ....................... 7 DRUM REPLACEMENT ..........................7 DAILY CARE..............................
  • Page 3: Ec Declaration Of Conformity

    Dear customer, We thank you very much for purchasing our extrusion pump model 12.22. You are the owner of one of the most reliable pumping system available on the market. Special care has been taken during all designing and manufacturing process to make sure your investment will provide full satisfaction.
  • Page 4: Technical Features

    3. TECHNICAL FEATURES The 12.22 pump is a feed piston pump, powered by an air motor. It is designed to dispense thick materials such as : mastics, pasty materials, glues, to extrusion or spray guns.
  • Page 5: Installation

    Maximum fluid pressure at the outlet of the pump P prod : xx bar / xx psi P air : 6 bar / 87 psi Air supply maximum pressure of the pump motor Serie / Serial Number given by KREMLIN REXSON KREMLIN Page 4 Manual : 573.049.112...
  • Page 6: Operating Principle

    When air pressure is applied on (15) (level 14 in a bottom position), the pressure force is exerted downwards and the pump is going down. When air pressure is applied on (16) (level 14 in a top position), the pressure force is exerted upwards and the pump is raising. KREMLIN Page 5 Manual : 573.049.112...
  • Page 7: Start Up

    6. START UP Start up procedure : Fill up the pump wetting cup with KREMLIN "T" lubricant (or an appropriate solvent). Unscrew the air regulators. Interconnect the equipment with the air pressure network (clean air - maxi 6 bar / 87 psi).
  • Page 8: Shutdown At End Of Work

    Move up level (14). The pump should raise and the drum should stay down. To restart the pump, refer to chapter 6. 9. DAILY CARE Comply with the usual instruction of gun servicing (refer to gun manual). KREMLIN Page 7 Manual : 573.049.112...
  • Page 9: Troubleshooting Chart

    Bad tightness of the valves. Clean them. The pump operates but provides an irre- Drain rod no tight enough. Tighten it. gular flow rate. Pressure on the follower plate too Increase the pressure. low. KREMLIN Page 8 Manual : 573.049.112...
  • Page 10: Servicing

    Reinstall the new reversing block in the reverse order of the disassembly sequence. 31.85 mm ±0.5 CAUTION : The number of spirals must equally be distributed on each fastening parts in order to get the above dimension. KREMLIN Page 9 Manual : 573.049.112...

Table of Contents