Advertisement
Quick Links
Advertisement
Related Manuals for JING YI JY-8050 Series
Summary of Contents for JING YI JY-8050 Series
- Page 1 JY-8050 SERIES LED BICYCLE LIGHT...
- Page 2 User manual Thank you for purchasing JY-8050 series Bicycle Light Device. This user manual has been specially designed to guide you through the functions and features of the device. 1. Product general description Front light Mode: High beam(3 LEDs)-Medium beam(2 LEDs)-Low beam(1 LED)–Flashing-Off...
- Page 3 Rear light Mode: Steady-Flashing-Eco Flashing (Short press the button on the controller to change the mode; Press and hold the button for 2 seconds to turn off the light from any mode) Function memory: when reopen, the function will continue the one used by last time Remote controller Two control button: one is for front light and the other one is for rear light...
- Page 4 Automatic shift function: the brightness will be shifted to low beam if the temperature of the device exceeds the safety temperature. On that case, the mode will not change even pressing the button. The mode would return to normal when the temperature of the device is lower than the safety temperature.
- Page 5 Green -- 100~75% Bule -- 75~50% Yellow -- 50~25% Red -- 25~5% Flashing Red -- 5% to Off...
- Page 6 2. LED specifications Light source: CREE XML-U2*3 (front light) 1-Watt LED (rear light) Luminous flux: 3000 lumens (front light) 50 lumens (rear light) LED lifespan: 50,000 hours 3. Battery specifications 6*18650 Li-ion batteries: 7.4V/6600mAh Batteries lifespan: 500 cycles of charging and discharging The battery capacity will fall by less than 10% after 500 cycles of charging and...
- Page 7 4. Operation of charging The battery has been partially charged at the factory. When charging is needed, please do as follows: Connect the charger to the battery Connect the charger to a wall outlet Red- charging Green- fully charged...
- Page 8 5. JY-8050 series Components Your package includes the following items: (1) Front light (2) Remote controller (3) Rear light (4) 7.4V/6600mAh battery pack (5) Charger (6) Front light extension cable(40CM) Rear light extension cable(61CM) (7) O-rings (2 PCS) (8) Velcro strap for cable management (9) Helmet elastic strap mount (Optional) ①...
- Page 9 ③ ④ 61cm 40cm ⑤ ⑥ ⑦ ⑧ ⑨ When using the helmet mount for the light, the battery is designed to be carried in a jacket pocket or a back pack, and do not connect a helmet mounted light to a bike mounted battery.
- Page 10 6. Assembling (a) put the O-ring on the front light (b)Fit the front light on the handlebar with the O-ring (c) Mount the rear light to the seat post...
- Page 11 (d)Wind the strap to the tube and make sure the battery is tightly fastened (e) Fix the remote controller to the handlebar...
- Page 12 (f) Connect the cables of the front light and the remote controller Connect the cables of the rear light and the remote controller Connect the cables of the battery and the remote controller Please use the Velcro strap to protect the wire from kinking or to keep it bound to the tube Please use the extension cable if necessary...
- Page 13 7. Warning Read instructions carefully before use. Failure to comply with the safety instructions may lead to damage to the charge and\or batteries and may cause serious injury to the user or other person. Keep out of reach of children Do not stare at the light source or point the light against other people’s eyes, as the powerful light may cause unexpected...
- Page 14 Do not drop or cause an impact to the charger or the battery, and never Never crush or puncture the battery Do not charge the battery with chargers that are not approved by the manufacturer Never dispose of batteries or devices in a fire Never place batteries or devices on or in heating devices, such as microwave ovens, stoves, or radiators.
- Page 15 between the + and – terminals of the device and lead to temporary or permanent battery damage To ensure proper functioning of the charge, keep the battery pack and charger free from dust & dirt. To clean the charger, disconnect it from the power supply and use a dry cloth only.