Labeling The Video Input Sources - Toshiba 56HM195 Owner's Manual

Labeling the video input sources

You can label each video input source according to the type of
device you connected to each source, from the following preset
list of labels:
– – (default label)
Hide (to hide an unused input in the Input Selection
window)
Audio Receiver
VCR
Video Recorder
Laser Disk
Compact Disc
DVD
DTV
Satellite/DSS
Cable
Game Console
Note:
• If you set up devices in TheaterNet,™ the associated inputs are
automatically labeled and cannot be relabeled until you remove the
device from TheaterNet (see page 45).
• If you set up a cable box in VIDEO 1, that input will be labeled
automatically and cannot be relabeled until you remove the device
from the TV Guide On Screen™ setup.
• You cannot select IEEE1394 devices through the Input Selection
window; however, you can select and control IEEE1394 devices
through TheaterNet (see page 45).
To label the video input sources:
1. Press MENU and open the Preferences menu.
2. Highlight Input Labeling and press ENTER.
3. Press y or z to highlight the video source you want to
label.
Preferences
Favorite Channels
Closed Caption Mode Off
Closed Caption Advanced
Input Labeling
Menu Language English
Home CH Setup
Navigate Back
Select CH RTN EXIT
Input Labeling
Video 1 DVD
Video 2 Cable
Video 3 Audio Receiver
ColorStream HD 1 Video Receiver
ColorStream HD 2 Hide
HDMI 1 DTV
HDMI 2 Satellite/DSS
ANT 2 - -
Reset Done
68
Chapter 8: Using the TV's features
Exit
Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.
4. Press x or • to select the desired label for that input source.
If a particular input is not used, you can select "Hide" as
the label, which will cause that input to be "grayed out" in
the input list and skipped over when you press the INPUT
button on the remote control.
Note: If you select "Hide" for all of the input labels, the POP
feature will be disabled. If you then attempt to access the POP
feature, the message "NOT AVAILABLE" will appear on-screen.
5. To save the new input labels, highlight Done and press
ENTER. To revert to the factory default labels, highlight
Reset and press ENTER.
Input labeling example:
The screen below left shows the default Input Selection screen
(with none of the inputs labeled). The screen below right is an
example of how you could label the inputs if you had connected
a DVD player to VIDEO 1, Cable TV to VIDEO 2, an audio
receiver to VIDEO 3, a video recorder to ColorStream HD1, a
DTV set-top box to HDMI 1, and a satellite/DSS set-top box to
HDMI 2. Also note that the ColorStream HD2 input is labeled
"Hidden," which means that the input will be skipped over
when INPUT or TV/VIDEO is pressed.
Input Selection
ANT 1
0 ANT 1 ANT 1
1 Video 1
2 Video 2
3 Video 3
4 ColorStream HD1
5 ColorStream HD2
6 HDMI 1
7 HDMI 2
8 ANT 2
0 - 8 / INPUT to Select
Input Selection screen
with no inputs labeled
To clear the input labels:
1. Press MENU and open the Preferences menu.
2. Highlight Input Labeling and press ENTER.
3. Highlight Reset and press ENTER.
Note: If you set up a device in TheaterNet, its input label will
not be cleared unless you remove the device from TheaterNet
(see page 45).
Input Selection
ANT 1
0 ANT 1 ANT 1
1 DVD
2 Cable
3 Audio Receiver
4 Video Receiver
5 ColorSteram HD2 (Hidden)
6
DTV
7 Satellite/DSS
8 ANT 2
0 8
- / INPUT to Select
Input Selection screen with
all inputs labeled except input 5,
which has been hidden.