Advertisement
Do Not operate polisher if any parts are damaged or missing. This may cause failure and/or injury.
8
wArNiNG! Do Not polish any materials containing asbestos.
‰
Do Not carry the polisher by the electrical cable.
8
Do Not use polisher with water, get the polisher wet or use in damp or wet locations, the polisher is for dry use only.
8
Do Not operate polisher if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
Do Not use where there are flammable liquids, solids or gases such as paint solvents or waste wiping or cleaning rags.
8
Do Not leave the polisher running unattended.
8
Do NoT carry the polisher with your finger on the power switch.
8
When not in use disconnect from power supply and store in a safe, dry, childproof area.
9
1.3.
LEAD PAINT WARNING!
Paint once contained lead as a traditional ingredient. The dust from the removal of such paint is toxic if inhaled or ingested and must,
therefore, be avoided. The following action must be taken before using the polisher on a surface that you suspect may have contained
lead in the paint.
1.
User must determine potential hazard relating to age of paint to be removed. (Modern paints do not contain lead).
DANGer! Keep all persons and pets away from the work area. The following are particularly vulnerable to the effects of lead paint dust:
2.
Expectant women, babies and children.
3.
We recommend personal protection by using the following safety items:
a) Paint Spray Respirator (Sealey ref: SSP1699)
b) PE Coated Hooded Coverall (Sealey ref: SSP266)
c) Latex Gloves (Sealey ref: SSP24)
4.
Take adequate measures to contain the paint dust, flakes, and scrapings.
5.
Continue to wear safety equipment as in 3 above, and thoroughly clean all areas when task is complete. ensure that paint waste is
disposed of, in sealed bags or containers, according to local authority regulations.
2. iNtroDuctioN
Rotary spot polisher kit designed for spot polishing. Ergonomic slim body design. Six stage variable speed control from 700-2500rpm.
Spindle lock for easy pad and shaft changes. Soft start for greater control. Fitted with 5m mains cable. Supplied with full spot polishing
kit, side handle and spare brushes.
3. speciFicAtioN
Model No: ................................................................... spk600
Pad Size: ......................................................................... Ø1-3"
motor Power: ................................................................... 600W
Supply: ............................................................................. 230V
Free Speed: ......................................................... 700-2500rpm
Thread size .........................................................................m14
Cable length .........................................................................5m
4. operAtioN
fig.1
wArNiNG! Before use, ensure that you have read and understood Section 1 Safety Instructions.
‰
4.1.
Attach the side handle by screwing into which side location is required.
4.2.
Screw required polishing disc and drive shaft into machine head. Depress the spindle lock (fig.2) to enable the drive shaft to be firmly
engaged in the machine head using the supplied spanner.
4.3.
Plug the polisher into the electric power supply.
4.4.
Grip the side handle and turn on by pressing the On/Off switch (fig.2). Pressing the button forward and down will hold the trigger and
allow for continuous running.
4.5.
To stop the polisher, depress the trigger and slide backwards to the off location.
4.6.
The speed of the sander can be adjusted using the speed control wheel on the end face of the polisher (fig.2). Rotate the control
clockwise to increase the speed or anti-clockwise to reduce the speed.
4.7.
Check that the unit is working correctly before use.
Note: The polisher is designed for dry use only. Do Not use with water or any other liquids.
© Jack Sealey limited
Original Language Version
fig.2
SPK600
Issue:2 (3,F)
17/07/19
Advertisement
