Changing Cooking Control Method; Using The Timer; Updating Firmware - Hatco Boxer IRNGBX Series Installation And Operating Manual

OPERATION

Changing Cooking Control Method

Two cooking control methods are available on the Induction
Range: Power Control and Temperature Control (Fahrenheit or
Celsius). To change control methods:
1. Press the Button on the control panel to toggle through
the cooking control methods. The screens appear in the
order shown below.
Power °F Temperature
Control
2. Turn the Control Knob to adjust the setting on the desired
screen.
• Turn the Control Knob clockwise to increase the setting.
Turn the Control Knob counterclockwise to decrease the
setting.
NOTE: Settings in Power Control do not correspond to the
temperature setting in Temperature Control.
General Setting Information
Hatco recommends adjusting the Power or Temperature
settings up or down while cooking to find the best setting for
a particular pan, amount of food, and heating desired. Once a
good setting has been determined, use this setting in the future
for cooking similar batches of the same size, in the same pan.
Power Control Information
Power Control supplies a continuous amount of heat to the
pan, similar to the operation of a gas or electric burner. The
Power setting is based on the amount of heat wanted in the
pan. Observe the cooking of the food in the pan and make
adjustments to the Power setting as necessary.
Temperature Control Information
Temperature Control regulates power to the pan on and off to
maintain the Temperature setting selected (Fahrenheit [ºF] or
Celsius [ºC]). Power is controlled automatically by the internal
computer. The temperature setting is approximate. The actual
temperature of the food in the pan will depend on the type and
size of the pan as well as the type and amount of food that is
in the pan.
NOTE: A setting in ºF Temperature Control is converted to the
corresponding setting when changing to ºC Temperature
Control.
°C Temperature
Control Control

Using the Timer

A timer is available on the Induction Range.
1. Place an induction-ready pan on the unit.
2. Press the button to turn on the unit.
3. Press the Button to toggle to the desired cooking control
method.
4. Press the button on the control panel.
• The Timer LED display will illuminate
and show four zeros.
5. Turn the Control Knob to the desired timer setting.
6. When the time on the Timer LED display begins counting
down, turn the Control Knob to set the desired power/
temperature setting.
• When the timer reaches zero, the
Timer LED display flashes "donE",
The Power/Temperature display goes
blank, and heat generation stops.
7. Press the button to rest the timer to zero.
8. Repeat steps 3–7 to continue timed cooking.

Updating Firmware

Use the following procedure to upload firmware updates to the
Induction Range from an external USB drive.
NOTE: For the latest firmware updates, cooking tips, and
more, go to the Hatco Induction Range website:
www.hatcocorp.com/rapide_cuisine
1. Press the button to turn on the unit.
2. Press and hold both the
buttons until "UI", "cb", or "UEr" appears
on the Power/Temperature LED display.
3. Insert the USB drive into the USB port.
• The USB port is on the under-side of the unit, near the
front.
4. Depending on the type of update, turn the Control Knob to
show either "UI" or "cb" on the Power/Temperature LED
display, then push the Control Knob to select and start the
update.
• A number indicating the percentage
complete will show on the Power/
Temperature LED display indicating
the update is in progress.
• When the update is complete, the displays will show
"success", and the unit will shut down.
• If the update was not successful, "fail" will show on the
Power/Temperature LED display. Perform the above
procedure again. If "fail" continues to show, contact
Hatco for assistance.
NOTE: If no USB drive is present, the displays will show the
error message "no USb".
8
English
Timer LED Display
Timer LED Display
and
Power/Temperature
LED Display
Power/Temperature
LED Display
Form No. IRNGBXM-1219