VEF TA-204 Manual

VEF TA-204
INTRODUCTION
This manual is made in order to familiarize you with your phone set. In order to get maximum benefits of this product, we suggest that you read
the User's manual carefully before using your phone set.
FEATURES
FSK/DTMF dual system Auto switch, FSK message auto-adjusts the time of the unit.
LCD displays incoming number, date, time, and total incoming calls.
Outgoing dialed number and conversation time review and redial back.
Local area code setting.
Fast checking the incoming call by calling number and calling date & time.
On-hook pre-dial and edit dialing number.
Key lock: lock off/lock "0"/ all key lock. (110,119,120,122, 200,800 available).
Hand-free dial and speak, conversation time display.
P/T, ringer HI/Low, Volume HI/LOW adjustable.
16 kinds of melody selection.
20 one-touch memories and 12 two-touch memories.
INSTALLATION
This phone requires 3 AAA-sized 1.5V batteries. Open the battery compartment cover and insert the batteries in the right polarity, then close the
cover. When you find that LCD display becomes very dark or incoming LCD not lighted, or some function is not correct, please change the
batteries.
Plug line cord into jack at the rear of the telephone base, the other end of the line cord connects to telephone line. Plug coiled cord into handset
modular jack. Plug the other end into the jack at the left side of the telephone. Set ringer volume according to your personal preference. Set the
P/T switch as required by your telephone exchange.
Caller ID function is available only after you apply this service to the local telecom company.
SYSTEM SET UP
At on-hook state, press SET to enter the set function, LCD will display the item to set. You can press UP or DOWN to select the different item
you would like to set up. When you choose one item, press SET again to go into the setting and use UP or DOWN to change the different
setting. When finished, press SET to go into the next item setting. You can leave the set up mode at any time by pressing DEL key.
The detailed setting steps are the following:
SETTING THE DATE
SET YEAR
Press the SET, LCD will display SET 1 DATE, press SET again to enter the setting date mode. The digit for year 2002 (represents the YEAR) will
illuminate on the LCD and 01 will flash, press UP or DOWN to edits the YEAR, then press SET to confirm and carry on the next step-set the
MONTH.
SET MONTH
The digit 1 M 1 D 00:00 (represents the MONTH, DATE, HOUR: MINUTE will illuminate on the LCD and 1 will flash, press UP or DOWN to edit
the MONTH, then press SET to confirm and carry on the next step-set the DATE.
SET DATE
The digit for 1 M 1 D 00:00 (represents the MONTH, DATE, HOUR: MINUTE) will illuminate on the LCD and 1 will flash, press UP or DOWN to
edit the DATE, then press SET to confirm and carry on the next step-set the TIME CLOCK: MINUTE. Then the LCD automatically changes the
Week of that day.
SET TIME
The digit for 1 M 1 D 00:00 (represent the MONTH, DATE, HOUR: MINUTE) will illuminate on the LCD and 0 will flash, press UP or DOWN to
edit the first digits of HOUR, then press SET to confirm and carry on the next step-set the second digits of HOUR. 0 will flash, press UP or
DOWN to edit the second digits of HOUR, then press SET to confirm and carry on the next step-set the first digits of TIME: MINUTE. 0 will flash,
press UP or DOWN to edit the first digits of TIME MINUTE, then press SET to confirm and carry on the next step-set the second digits of TIME:
MINUTE. 0 will flash, press UP or DOWN to edit the second digits of TIME: MINUTE, then press SET to confirm and carry on the next step
CODE
SETTING THE AREA CODE
LCD will display SET 2 ACODE; press SET to enter the set mode. LCD will display CODE - - - - - and - will flash to indicate to set ACODE. Press
UP or DOWN to adjust the AREA CODE number and press SET to confirm. Repeat this operation to the last digit. You only need to set 5 digits,
if it is 4-digit, you need to press SET twice to exit.
SET FLASH TIME
LCD will display SET FLASH ; press SET to enter the set mode. LCD will display FLASH 1 600- and - will flash to indicate the default flash time is
600 mini-second. Press UP or DOWN to select the right flash time and to press SET to confirm. There are four kinds of choices: 110ms,
300ms，600ms, and 1000ms.
SETTING LCD BRIGHTNESS
LCD will display SET 4 LCD，press SET to enter, and then LCD will display LCD 3 to indicate the default LCD brightness is in 3 step. Press UP
or DOWN to select the right LCD brightness, then press SET to confirm. There are five steps of LCD brightness for your selection.
SET ALARM CLOCK
LCD will display SET 5 ALARM，press SET to enter, and then LCD will display 1 12:00 OFF to indicate the default ALARM is off. This
telephone has 3 groups of ALARM CLOCK setting. Press UP or DOWN to select the groups of ALARM CLOCK; press SET + UP or DOWN to
set the HOUR; Press SET + UP or DOWN to set the MINUTE; Press SET + UP or DOWN to set the ALARM ON/OFF. then press SET to
confirm.