1. Manuals
  2. Brands
  3. HIKOKI Manuals
  4. Construction Equipment
  5. VB 3616DA
  6. Handling instructions manual

HIKOKI VB 3616DA Handling Instructions Manual

Hide thumbs Also See for VB 3616DA:
Table of Contents

Advertisement

Quick Links

Download this manual
VB 3616DA
Handling instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VB 3616DA and is the answer not in the manual?

Questions and answers

Related Manuals for HIKOKI VB 3616DA

Summary of Contents for HIKOKI VB 3616DA

  • Page 1 VB 3616DA Handling instructions...
  • Page 2 &...
  • Page 3 & Ⓐ Ⓑ...
  • Page 4 & &...
  • Page 5 &...
  • Page 6 ø ø ø 45° 90° 135° 180° 180° 135° 45° 90°...
  • Page 7 ≥ 200 mm Ⓡ Ⓛ Ⓛ Ⓡ...

  • Page 9: General Power Tool Safety Warnings

    c) Prevent unintentional starting. Ensure the GENERAL POWER TOOL SAFETY switch is in the off -position before connecting WARNINGS to power source and/or battery pack, picking up or carrying the tool. WARNING Carrying power tools with your fi nger on the switch Read all safety warnings, instructions, illustrations and or energising power tools that have the switch on specifi...

  • Page 10: Additional Safety Warnings

    Contact the store where you bought the unit from other metal objects, like paper clips, coins, or a HiKOKI Authorised Service Center, and ask for keys, nails, screws or other small metal objects, checkup and/or repair. Use of the unit without checkup that can make a connection from one terminal to and repair can result in injury.

  • Page 11: Caution On Lithium-Ion Battery

    9. Make sure that the battery is installed fi rmly. If it is at all 2. Do not pierce battery with a sharp object such as a loose it could come off and cause an accident. nail, strike with a hammer, step on, throw or subject the 10.
  • Page 12 ○ If the BSL36B18 is installed in the power tool, the power Grip rubber output will exceed 100 Wh and the unit will be classifi ed as Dangerous Goods for freight classifi cation. Motor Switch trigger & Power Output Handle Switch lock Battery 2 to 3 digit number...

  • Page 13: Standard Accessories

    Battery No-load speed Remaining battery indicator switch Weight Lights ; The battery remaining power is over 75% Switching ON Lights ; The battery remaining power is 50% – 75%. Switching OFF Lights ; The battery remaining power is 25% – 50%. Lights ;...
  • Page 14 NOTE CHARGING Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to Before using the power tool, charge the battery as follows. change without prior notice. 1. Connect the charger’s power cord to the receptacle.

  • Page 15: Prior To Operation

    (2) Regarding the temperatures and charging time of the rechargeable battery The temperatures and charging time will become as shown in Table 2. Table 2 Charger UC18YSL3 Type of battery Li-ion Temperatures at which the 0°C – 50°C battery can be recharged Charging voltage 14.4 Multi volt...
  • Page 16 5. Removing and inserting the battery cover and battery (Fig. 5) WARNING Make sure the battery cover is attached when operating the tool. Iron fi lings in the battery terminal area may result in malfunction. 6. Remaining battery indicator (Fig. 6) PICTGRAPH ILLUSTRATION AND EXPLANATION Warning label (Cutting) Avoid bringing your hand near to the reaction stoppers during operation;...

  • Page 17: Operation

    (For replacing the grip rubber and repairing, ask the store where you purchased CAUTION it or the HiKOKI Authorized Service Center.) Pull out battery before carrying out any adjustment, (1) Position the tool as shown in Fig. 9.
  • Page 18 3. Cutter Replacement (1) Remove battery cover and battery (Fig. 5-a) After following the steps for “1. Inspect the cutter and grip (2) Make sure the switch lock is in the lock position. (Fig. 17) rubber” (steps (1) through (5)), follow the instructions below. (3) Position the tool so that the turn table is facing upwards Replace the upper and lower cutters as one set.

  • Page 19: Warning Signals

    2. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be Important notice on the batteries for the HiKOKI loose, retighten them immediately. Failure to do so could cordless power tools result in serious hazard.

  • Page 20: Troubleshooting

    TROUBLESHOOTING Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your dealer or the HiKOKI Authorized Service Center. 1. Power tool Symptom Possible cause Remedy Does not move No battery remaining.
  • Page 21 The charger’s vents are blocked, causing its Avoid blocking the vents. internal components to overheat. The cooling fan is not running. Contact a HiKOKI Authorized Service Center for repairs. The USB power lamp The battery’s capacity has become low. Replace the battery with one that has has switched off...
  • Page 22 VB3616DA (2XC) (NNK) 5 mm ― BSL36A18 ― UC18YSL3 ―...
  • Page 23 BSL36A18 319706 50 mm (R25 mm) BSL36B18 321446 D 38 38 mm (R19 mm) 321445 UC18YSL3 (14.4V - 18V) 329897 ET36A 375990...
  • Page 24 Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. C99737111 N Printed in Japan...

Table of Contents