IBM 29 Card Punch Field Engineering Maintenance Manual page 5

4.10 Program Drum Unit .
4.10.1 Sensing Assembly Service Check
4.10.2 Sensing Assembly Adjustments .
4.10.3 Sensing Assembly Removal and Replacement
4.10.4 Program Cam Contacts Service Check
4.10.5 Program Cam Contacts Adjustment
4.10.6 Program Drum Interlock Arm (Split Hub)
Adjustment
4.11 Print Unit .
4.11.1 Print Assembly Service Checks.
4.11.2 Print Assembly Adjustments .
4.11.3 Print Assembly Removal and Replacement
4.11.4 Ribbon Feed Pawl Adjustment
4.11.5 Print Drive Adjustment .
4.11.6 Print Suppress Magnet Adjustment
4.12 Keyboard . .
4.12.1 Contact Adjustments
4.12.2 Hook Support Bar Adjustment
4.12.3 Permutation Bar Adjustment
4.12.4 Restoring Magnet Adjustment .
Illustrations
Figure Title
Chapter 1. Reference Data and Service Aids
1-1 Characteristics
1-2 Operations
1-3. Sequence of Operations
1-4 Diagnostic Flowchart Symbols
1-5 Start and Run Failures .
1-6 Card Transport Failures
1-7 Interposer Selection Failures
1-8 EscapementFailures (Part 1 of 2).
1-8 |Escapement Failures (Part 2 of 2).
1-9 Punch Drive Cycle Failures
1-10 Print Control Failures
1-11 Test Probe
1-12 Reed Relay Insertion
Chapter 2. Console and Maintenance Facilities
2-1 Program Card - Model A
2-2 Program Card — Model B
Chapter 3. Preventive Maintenance
3-1 Preventive Maintenance Routines .
3-2. ~=Lubrication — Right Front .
3-3. ~Lubrication — Front
3-4 Lubrication — Front (Machine Bed Tilted)
3-5 Lubrication — Rear .
3-6 Punch Unit Lubrication
3-7 Keyboard Lubrication .
Chapter 4. Checks, Adjustments, and Removals
4-1 Friction Drive Adjustment.
4-2 Escapement Adjustment (Part 1 of 2)
4-2. Escapement Adjustment (Part 2 of 2)
4-3. Hopper Adjustment.
iV
4-20
4-20
4-20
4-22
4-22
4-22
4-22
4-22
4-22
4-29
4-33
4-36
4-36
4-36
4-37
4-37
4-38
4-38
4-38
Page
1-1
1-1
1-2
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
. 1-10
2-2
2-2
3-3
3-4
3-5
3-6
3-7
3-8
4-1
4-2
4-4
4.12.5 Upper Permutation Support Adjustment.
4.12.6 Key Unit Adjustment
4.12.7 Key Unit Removals .
Section 2. Features.
Chapter 5. Power Supplies
Section 1. Basic Unit
Section 2. Features.
Chapter 6. Locations
6.1 Keystem Numbering
6.2 Reed-Relay Card
6.2.1 Reed Relays .
6.3 Wire-Contact Relays
6.4 Standard Modular System (SMS) .
6.4.1 SMS Card Receptacles . .
6.4.2 SMS Locations and Pin Numbering
6.5 Location Figures
Index
Figure Title
4-4 CF Clutch Magnet Adjustment
4-5 CF Clutch Adjustment . .
4-6 CF Latch Magnet Adjustment .
4-7 Pressure Rail Adjustment
4-8 Pressure Rail — Card-Lever Contact
4-9 Card Guide — Detail Station
4-10 Card Guide — Master Station
4-11 Detail Card Registration
4-12 Pressure Roll Adjustment . .
4-13 Master Station Registration Adjustment .
4-14 Armature Pivot Adjustment .
4-15 Armature Pivot Adjustment — Side View
4-16 Armature Adjustment .
4-17 Interposer Unlatching Clearance
4-18 Interposer Relatching Adjustment
4-19 Armature Unlatching Clearance
4-20 Interposer Bail Contact Adjustment
4-21 Interposer Bail Contact Rise Adjustment
4-22 Print Drive Unit Cam Timing
4-23 Punch Clutch Magnet
4-24 Punch Clutch Components .
4-25 Punch Clutch Adjustment .
4-26 High-Speed Circuit Breaker
4-27 Punch Bed — Front View
4-28 Punch and Extension
4-29 Punch Penetration Adjustment
4-30 Sensing Pin Contact Adjustment
4-31 Pin Sensing Adjustment
4-32 Stacker Timing
4-33 Stacker Adjustment .
4-34 Traveling Card Guide
4-35 Timing Tool .
4-36 Program Unit Timing Chart
4-39
4-39
4-40
4-41
5-1
5-1
d-1
6-1
6-1
6-1
6-2
6-3
6-3
6-3
6-3
6-5
Page
4-5
4-5
4-5
4-6
4-6
4-6
4-6
4-7
4-8
4-8
4-9
4-9
4-10
4-10
4-10
4-11
4-11
4-11
4-12
4-12
4-13
4-13
4-14
4-15
4-15
4-16
4-17
4-17
4-18
4-19.
4-19
4-20
4-21