1. Manuals
  2. Brands
  3. ASCENTO Manuals
  4. Water Pump
  5. PRJ062
  6. Instruction manual

ASCENTO PRJ062 Instruction Manual

External pressure pumps
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
1 |
P a g e
A S C E N T O G R O U P A U S T R A L I A
P : 1 8 0 0 8 0 7 6 0 4
E : s a l e s @ a s c e n t o . c o m . a u

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PRJ062 and is the answer not in the manual?

Questions and answers

Related Manuals for ASCENTO PRJ062

Summary of Contents for ASCENTO PRJ062

  • Page 1 P a g e A S C E N T O G R O U P A U S T R A L I A P : 1 8 0 0 8 0 7 6 0 4 E : s a l e s @ a s c e n t o . c o m . a u...
  • Page 2 P a g e A S C E N T O G R O U P A U S T R A L I A P : 1 8 0 0 8 0 7 6 0 4 E : s a l e s @ a s c e n t o . c o m . a u...
  • Page 3 P a g e A S C E N T O G R O U P A U S T R A L I A P : 1 8 0 0 8 0 7 6 0 4 E : s a l e s @ a s c e n t o . c o m . a u...
  • Page 4 P a g e A S C E N T O G R O U P A U S T R A L I A P : 1 8 0 0 8 0 7 6 0 4 E : s a l e s @ a s c e n t o . c o m . a u...

  • Page 5: Performance Data

    ASCENTO GROUP AUSTRALIA P: 1800 807 604 F: 1800 807 609 E: sales@ascento.com.au INSTRUCTION MANUAL & WARRANTY EXTERNAL CONSTANT PRESSURE PUMPS APPLICATION: CONSTANT PRESSURE PUMPS are fit for purpose when installed correctly according to these instructions; For pumping of Clean Fresh Water at a temperature of +5°C to +40°C to: Garden Taps, Houses, Sheds, Cabins, Pressure Boosting, Clean Water Transfer, suitable Rain-to-Mains Systems (370Watt and greater motor size) and for no other use.
  • Page 6 6. IMPORTANT NOTE re PUMP NOISE: Avoid installing pumps near bedrooms or neighbours bedrooms. Particularly JET pumps, due to their self-priming design they typically make more noise than a MULTISTAGE Pump. This is a feature of the pump design, it is not a fault, and is not a cause for warranty claims, as it is not a product fault.

  • Page 7: Overload Protection

    15. PUMP PRIMING AND START UP (a) Dry operation will destroy the pump seals and is not covered by warranty. (b) Remove the pressure controller by loosening the barrel union, (or use the priming plug at the front of the wet-end, near the inlet, but that is slower) and completely fill the pump chamber with water before starting.

  • Page 8: Troubleshooting Checklist

    NOTE: if pipe from tank to pump is not straight it will most likely get air-locks in the pipe, and the pump might not shut down properly when the tank is low, as it is getting some air, some water - this is not a fault – simply turn the pump off until the tank fills to have 500mm depth or more.

  • Page 9: Electrical Precautions

    25. Safety Switch (RCD) or Circuit Breaker trips when the pump starts 1. Circuit is overloaded with too many appliances connected to it > contact a licenced electrician to install additional circuit 2. Power plug is wet > refer 21. 3.

  • Page 10: Warranty Conditions

    • W: www.ascento.com.au © COPYRIGHT 2019 No part of this publication is to be copied stored or distributed in any manner or form without the prior written permission of Ascento Group Australia. E&EO. 10 | P a g e...

Table of Contents