Advertisement
Quick Links
IMPORTANT SAFETY INSTRUCTIONS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED.
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D'INSTALLATION PERTINENT, PAR UNE
PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES
RISQUES INHÉRENTS.
1.
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS.
2.
INSTALLATION REQUIRES
KNOWLEDGE OF LED LIGHTING AND
ELECTRICAL SYSTEMS. RISK OF FIRE OR
ELECTRICAL SHOCK EXISTS.
3.
DO NOT MAKE OR ALTER ANY
OPEN HOLES IN AN ENCLOSURE OF
WIRING OR ELECTRICAL COMPONENTS
DURING KIT INSTALLATION.
4.
DO NOT EXPOSE WIRING TO EDGE
OF SHARP OBJECTS IN ORDER TO
PREVENT WIRING DAMAGE OR ABRASION.
5.
THE LED LUMINAIRE MUST BE
WIRED IN ACCORDANCE WITH THE
NATIONAL ELECTRICAL CODE AND
APPLICABLE LOCAL CODES.
6.
PROPER GROUNDING IS REQUIRED
FOR SAFETY.
7.
THIS LED LUMINAIRE MUST BE
INSTALLED PER THE APPLICABLE
CITYSAVER™ LED
ROADWAY LUMINAIRE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT. DO NOT
ATTEMPT INSTALLATION IF THIS
CONDITION IS NOT MET. CONTACT A
QUALIFIED ELECTRICIAN.
8.
DO NOT USE THIS LUMINAIRE FOR
ANYTHING OTHER THAN ITS INTENDED
USE.
9. DANGER-RISK OF
FIRE OR ELECTRICAL
SHOCK-DISCONNECT
POWER BEFORE
BEGINNING
INSTALLATION.
Advertisement
Summary of Contents for XtraLight CITYSAVER
- Page 1 CITYSAVER™ LED ROADWAY LUMINAIRE IMPORTANT SAFETY INSTRUCTIONS THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES...
-
Page 2: Installation
CITYSAVER™ LED ROADWAY LUMINAIRE INSTALLATION THIS FIXTURE IS INTENDED FOR 2” or 1-1/4” NPS (2.38”/60mm or 1.67”/42mm OD) MAST ARM MOUNTING ONLY Tools needed: 9/16” Socket wrench Straight blade screwdriver 1. Open the door by loosening both door screws. (See Figure 1) - Page 3 2” NPS (2.38”/60mm OD nominal). To install the luminaire on a 1-1/4” NPS mast arm, insert the mast arm into the back of the CitySaver luminaire through the bird guard and into the pipe clamp(s). For a mast arm larger than 1-1/4” NPS and up to 2” NPS, remove the knockout from the bird guard.
- Page 4 CITYSAVER™ LED ROADWAY LUMINAIRE 3. Level orientation of luminaire is required. Use steps to compensate, from +5⁰ to -5⁰, for mast arms that are not level. (See Figure 3) Use the bubble level inside the electrical compartment to level the fixture.
- Page 5 CITYSAVER™ LED ROADWAY LUMINAIRE 4. Bring the electrical wires into the CitySaver luminaire and connect them to the terminal block inside the electrical compartment. Be sure to connect the line wire to the “L” terminal, the ground wire to the center terminal and the neutral wire to the “N”...
- Page 6 CITYSAVER™ LED ROADWAY LUMINAIRE 5. Close the door by tightening the two door screws until firmly seated. 6. A photocontrol or shorting cap is required for luminaire operation. Install either a PC or SC into the NEMA receptacle in the top of the luminaire following manufacturer’s recommendations. (See Figure 6) If photocontrol receptacle rotation is required for North orientation, loosen the two slotted head screws.
- Page 7 CITYSAVER™ LED ROADWAY LUMINAIRE Luminaire Dimensional Data City Saver Small Luminaire EPA: 0.72 sq. ft. Weight: 14 lbs. City Saver Medium Luminaire EPA: 1.14 sq. ft. Weight: 22 lbs.
- Page 8 CITYSAVER™ LED ROADWAY LUMINAIRE IN0006 Rev. 3 09/08/2016...