Related Manuals for SpectraLink DECT Repeater
Summary of Contents for SpectraLink DECT Repeater
- Page 1 Spectralink DECT Repeater Installation Guide 14183300-IG, Edition 11.0 February 2020, Original document...
- Page 2 The drawings and specifications contained herein are the property of Spectralink and shall be neither reproduced in whole or in part without the prior written approval of Spectralink, nor be implied to grant any license to make, use, or sell equipment manufactured in accordance herewith.
-
Page 3: Table Of Contents
Repeater Programming Kit Content of the Spectralink Repeater Programming Kit Set up of the Hardware for Repeater Programming Programming the Spectralink DECT Repeater with the Handset and Repeater Management Tool Numbering of Base Stations/Server 200/400 and Repeaters in a Normal... -
Page 4: About This Guide
Spectralink DECT Repeater Installation Guide About This Guide This guide explains how to install the Spectralink DECT Repeater. This guide is intended for qualified technicians and the reader is assumed to have a basic knowledge about the Spectralink IP-DECT/DECT/Virtual IP-DECT Server, Spectralink IP-DECT/Digital DECT Base Station and Spectralink DECT Repeater. - Page 5 Available online at http://support.spectralink.com/products. Spectralink DECT Training material In order to gain access to the Spectralink training mater- ial, you must attend training and become Spectralink Cer- tified Specialist. Please visit http://- partneraccess.spectralink.com/training/classroom-train-...
-
Page 6: Installing Spectralink Dect Repeater
Two mounting screws and anchors Description of Repeater The Spectralink DECT Repeater is a building block to be used to extend the coverage area in a wire- less Spectralink DECT solution. The repeater does not increase the number of traffic channels, how-... - Page 7 Spectralink DECT Repeater Installation Guide The repeaters are mainly used in areas with limited traffic. The Spectralink DECT Repeater is avail- able with either 2 or 4 traffic channels. It is wireless and does not need physical connection to the Spectralink IP-DECT/DECT/Virtual IP-DECT Server, making it very easy to install.
-
Page 8: Repeater Appearance And Components
Spectralink DECT Repeater Installation Guide Repeater Appearance and Components Below you will find a description of the repeater appearance and components: DECT Repeater - bottom DECT Repeater - rear RJ9 port Holes for wall mounted screws External antenna connector DECT Repeater - front 14183300-IG, Edition 11.0... -
Page 9: Repeater Led Indicators
Spectralink DECT Repeater Installation Guide Repeater LED Indicators Below you will find information about LED indicators on the repeater. Front Cover LED Indicator Meaning Indicator Off The repeater is not powered. Flashing Repeater has been powered, sync has still not been established. -
Page 10: How To Wall Mount The Repeater
Spectralink DECT Repeater Installation Guide How to Wall Mount the Repeater For best RF coverage, the device must be mounted vertically on walls. Caution: The repeater and external antenna is to be fixed-mounted on indoor permanent struc- tures providing a separation distance of at least 20 cm/8 inches from all persons during normal operation and must not be co-located or operating in conjunction with any other antenna or repeater. -
Page 11: Measurements And Mounting Template
Spectralink DECT Repeater Installation Guide Measurements and Mounting Template Measurements in Millimeters 14183300-IG, Edition 11.0 February 2020, Original document... - Page 12 Spectralink DECT Repeater Installation Guide Mounting Template Note: For correct measurement, ensure that this page is printed as either Actual size or Scale 100 % (Print dialog box) on an A4 size paper before using the mounting template below. 14183300-IG, Edition 11.0...
-
Page 13: Programming A Spectralink Dect Repeater With The Repeater Programming Kit
Spectralink DECT Repeater Installation Guide Programming a Spectralink DECT Repeater with the Repeater Pro- gramming Kit Content of the Spectralink Repeater Programming Kit The Repeater Programming Kit (Part no. 02509210) consists of: Splitter Programming tool with RJ-Connector USB cable Set up of the Hardware for Repeater Programming It is recommended that you carry out the set up in the following order: 1. -
Page 14: Programming The Spectralink Dect Repeater With The Handset And Repeater Management Tool
The Handset and Repeater Management Tool identifies the type of repeater, and with this software it is possible to program the Spectralink DECT Repeater to connect to the Spectralink DECT Radio Infrastructure solutions. -
Page 15: Numbering Of Base Stations/Server 200/400 And Repeaters In A Normal Configuration
Spectralink DECT Repeater Installation Guide Numbering of Base Stations/Server 200/400 and Repeaters in a Normal Configuration Note: Repeater and base station/server RPNs must not be the same. Also, in a situation where common overlap is present between the actual units, a repeater cannot have an RPN that is similar to that of a base station/server or another repeater. -
Page 16: Numbering Of Repeaters In A Repeater Daisy Chain Configuration
Spectralink DECT Repeater Installation Guide Numbering of Repeaters in a Repeater Daisy Chain Configuration First Repeater in Chain RPN of base station/server 200/400 + 64 Base to synchronize on: RPN of base station/server Second Repeater in Chain RPN of base station/server 200/400 + 128... -
Page 17: Using The Spectralink Dect Repeater With External Antenna17
Only the Spectralink external antenna (part no. 02319507 - including 1 m connection cable) is approved along with the Spectralink DECT Repeater. The external antenna is delivered with a 1 m connection cable. The connection cable is also available in 7.5 m (part no. -
Page 18: Alternative Synchronization Ways
Spectralink DECT Repeater Installation Guide Alternative Synchronization Ways The Spectralink DECT Repeater with or without external antenna, 4 channels, can be programmed to obtain synchronization on two radio units (base station, wireless server 200/400 or repeater). Note: The primary synchronization source has priority; the alternative synchronization source is only in use as long as the primary synchronization source is down. -
Page 19: Technical Specifications
Indoor: 20 - 50 m. (65 - 165 ft.) Outdoor: 300 m. (1000 ft.) Full slot DECT radio (12 channels) Possible to connect external antenna (Only Spectralink External Antenna can be used) ELECTRICAL REQUIREMENTS Maximum power consumption: 1.62W (Max. 2W) The power supply is 9VDC, 180mA. -
Page 20: Spectralink External Antenna
Spectralink DECT Repeater Installation Guide Spectralink External Antenna ELECTRICAL PROPERTIES Frequency range: 1880-1930 MHz Impedance: 50 Ω (DC-path to ground) Polarization: RHCP Gain: 7.5 - 8.0 dB 3 dB beamwidth horizontal: > 62° 3 dB beamwidth vertical: > 62° Front to back ratio: > 8 dB Return loss: <... -
Page 21: Product Compatibility
If you have any questions about product compatibility, contact your system administrator. You can use the Spectralink DECT Repeater with other Spectralink products as identified by the type approval model ID and/or part number located on the label of the product. - Page 22 Spectralink DECT Repeater Installation Guide Spectralink Base Station Spectralink IP-DECT Base Station 1G8 K005 Spectralink IP-DECT Base Station 1G9 K005 Spectralink Digital DECT Base Station 4 channels K007 Spectralink Digital DECT Base Station 8 channels K007 Power Supply, 8.0V DC (only Spectralink IP-DECT 84642600...
- Page 23 Spectralink DECT Repeater Installation Guide Spectralink DECT Media Resource Spectralink DECT Media Resource (only IP-DECT K006 Server 6500 and Virtual IP-DECT Server One) Spectralink Virtual IP-DECT Media Resource Spectralink Virtual IP-DECT Media Resource (only 14233270 Virtual IP-DECT Server One) 14183300-IG, Edition 11.0...
Need help?
Do you have a question about the DECT Repeater and is the answer not in the manual?
Questions and answers