Advertisement
RESETTING THE PROGRAMMER
Electronic equipment can in some circumstances be affected by electrical interference. If the
programmer's display becomes frozen or scrambled; or if you wish to revert back to the default time
settings please use the following procedure.
Lower the front flap of the unit. Press the ADVANCE and SELECT
buttons together then release the buttons and the programmer will
return to the preset factory settings.
The normal working position for the SET switch is in the PROG.RUN position. In order to remind the user
of this, the flap is unable to be closed with the switch in any other position.
The simple instructions below are designed to help with the programming of the unit. All the following
instructions require the front flap to be lowered. Please replace the flap when
normal operation is required.
SETTING TIME OF DAY
Move the SET
Use PLUS and
switch to the CLOCK
MINUS buttons to
position.
adjust time
DEFAULT TIME SETTINGS
1
ON 1
OFF 2
st
st
6:30
8:30
12:00
AM
AM
The default factory settings are shown above, however if you wish to change these proceed as
instructed below.
SETTING THE ON AND OFF TIMES
Move SET switch
Use the PLUS and
to the
MINUS buttons to
ON/OFF TIMES
adjust the 1st ON
position.
time.
Repeat this
process for 2nd and
switch to PROG.RUN
3rd setting.
Should you encounter any problems, please refer to the
Question and Answer section located on page 4
Page 2
FRONT COVER
SETTING
Return SET switch to
PROG.RUN position
SET
ON
2
OFF
3
ON
3
OFF
nd
nd
rd
rd
12:00
4:30
10:30
PM
PM
PM
PM
Use the PLUS and
Press
MINUS buttons to
ENTER
adjust the 1st OFF
time.
Return SET
SETTING 1ST
ON
OFF
position.
6:30
8:30
AM
AM
The SET slide switch must be in the PROG.RUN position for the following instructions.
Press SELECT once.
Programme goes from
AUTO to ALL DAY
ADVANCE
BOOST
Unit will operate from
first ON until last OFF
period
SELECT
10:00
Press BOOST button once:
Your System will be Boosted
for 1 hour
12:OO
PM
Press ADVANCE button once
1:45
PM
HOLIDAY FUNCTION
Move SET switch to the
HOLIDAY position
Whilst the HOLIDAY FUNCTION is in operation the system will remain OFF, the display will show the
number of nights remaining. The HOLIDAY setting is an instant function and cannot be set in advance.
The HOLIDAY FUNCTION can be cancelled at any time by pressing any of the SELECT buttons.Normal
programme functions will resume at the first ON period after the pre-set number of nights has expired.
Press
ENTER
Programming ON/OFF times
If a period is not required it can be cancelled by setting the ON and OFF settings to the same
time. Example ON 10:00am OFF 10:00am
Your programmer will prevent you from accidentally overlapping ON and OFF times.
Example: If the 2nd ON time is set at 12:00pm and then you try and set the 1st OFF at 12:30 pm the
OFF setting will 'bounce' by a 10 minute period until the 2nd ON time has been adjusted.
SPECIAL FEATURES
Press SELECT again.
Press SELECT again.
Programme goes from
Programme goes from
ALL DAY to ON
Unit will be
continuously ON
continuously OFF
10:00
AM
AM
ALL DAY
ON UNTIL
ON
8:30
PM
BOOST FUNCTION
-
1 or 2 hour temporary override
Press BOOST button twice:
Your System will be Boosted
for 2 hours
ADVANCE FUNCTION
-
Brings forward next on or off operation
To cancel the advance press the ADVANCE
button again. This will return the unit to
to move to the next
its normal programme
ON/OFF time
-
Allows system to be programmed for up to 32 days
Use the PLUS button to enter the
required number of nights
(MAX OF 32 NIGHTS)
INFORMATION AND ADVICE
Press SELECT again.
Programme goes from
ON to OFF
OFF to AUTO
Unit will be
Programmer will return
to normal ON and OFF
times
10:00
10:00
AM
AM
AUTO
ON UNTIL
OFF
10:30
AM
At any time during a BOOST
10:00
AM
period press BOOST again to
BOOST
AUTO
return to normal program-
ON UNTIL
11:30
ming
AM
Return SET switch to the
08
PROG.RUN position
SETTING
Page 3
Advertisement
