Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kuppersbusch EDG 650.0
Summary of Contents for Kuppersbusch EDG 650.0
- Page 1 Steam Cooker EDG 650.0...
- Page 2 Service Manual: H3-63-01 Responsible: D. Rutz KÜPPERSBUSCH HAUSGERÄTE AG Tel.: (0209) 401-733 Kundendienst Fax: (0209) 401-743 Postfach 100 132 Date: 20.07.2000 45801 Gelsenkirchen...
-
Page 3: Table Of Contents
Specifications ....................... 5 Installation ........................6 Fitting the steam cooker into a built-in unit............6 Electrical connection .................... 7 Features and operation of the EDG 650.0 ..............7 Operation ......................7 Control panel ......................8 3.3. Control panel ......................8 Information symbols and buzzer ................ -
Page 4: Introduction
Service Manual EDG 650.0 General How does steam cooking work? Steam Cooking is a technique for cooking food using pure steam. Steam is distributed evenly throughout the oven. Since the food is initially cooler than the steam, the steam condenses onto the cooler surface, transferring heat to the food. -
Page 5: Technical Data
Service Manual EDG 650.0 Specifications Model EDG 650.0 External dimensions (H x W x D) 374 mm x 544 mm x 410 mm Oven capacity 23.5 litres Net weight 25 kg Power supply 230V 50 Hz, 1.93 W Energy consumption 1.18 kWh... -
Page 6: Installation
Service Manual EDG 650.0 Installation Fitting the steam cooker into a built-in unit If the kitchen unit is not suitably heat resistant, it must be fitted with heat-shielding material. The dimensional specifications for installation are shown in the drawing. Place the cooker in the housing unit and make sure that it is level. -
Page 7: Electrical Connection
Make sure that the yellow/green earth lead is connected to the earthing point on the appliance and also to the mains cable. The plug must be fitted with a minimum 10 Amp fuse. Features and operation of the EDG 650.0 Control panel Interior Reservoir... -
Page 8: Control Panel
Service Manual EDG 650.0 Control panel Start/Stop Minus Defrost Plus Cook Timer Display Clock Cook Time/cooking time Timer Defrost Water level indicator Information symbols and buzzer The oven is fitted with user-friendly information symbols and a warning buzzer. Message Cause... -
Page 9: Cooking Settings
Service Manual EDG 650.0 Adjusting the settings on the cooker To select the cooking method, press either the button for cooking or for defrosting. Use the buttons to set the cooking time. Press Setting the timer Press the button. Use the buttons to set the cooking time. -
Page 10: The Cooking Process
Service Manual EDG 650.0 (6) Thermoactivator (11) Flap (7) Fan (5) Barrier mat Reservoir (2) Hydraulic pump (3) Water inlet tube (4) Steam generator (8) Overheat thermostat (9) Control probe The accessories are not shown in this illustration. The steam cooker is provided with a shelf for cooking utensils, a dish with a filter and an attachment for the steamer pan. -
Page 11: Opening The Door During Cooking
Service Manual EDG 650.0 4.2.1 Phase A: Changing air into steam / increasing the temperature The first phase takes 10 minutes. The thermoactivator is energized. Approx. 1 minute later, the control card activates the guide arm to close the flap. The steam generator heats up about 2.5 minutes, before the pump is activated via the control board (1.2 sec. -
Page 12: Water Level Sensor
Service Manual EDG 650.0 Water level sensor The water level is detected by a magnet (which is fixed to a float) and 4 reed switches. The magnet and the float are a fixed part of the reservoir. The 4 reed switches are mounted on a PCB, which is fixed to the reservoir bracket. -
Page 13: Testing And Measuring
Service Manual EDG 650.0 Testing and measuring Components Thermoactivator Undo one of the wires and check for a reading of 980 ohms at the end. Heat barrier! Undo one of the wires and check for a reading of 46 ohms at the lower surface terminal and 98 ohms on the upper surface terminal. -
Page 14: Reed Switches And Led's
Service Manual EDG 650.0 Reed switches and LED’s A fault with the reed switch card and the display card may be shown at the same time. It is therefore very important to find out which of these components is actually faulty. -
Page 15: Repair And Maintenance
Service Manual EDG 650.0 Maintenance and repair IMPORTANT: Before starting any repair or maintenance work, disconnect the appliance from the mains and connect all earth units. Make sure you have taken all necessary safety precautions before you begin. Cut off power to the appliance... -
Page 16: Removing The Lower Air Duct
Service Manual EDG 650.0 Removing the upper air duct Remove the upper air duct. Removing the tangent. Remove the 2 screws on the tangent and the 6 screws on the flap. Lift the air duct slightly and release the cable clamp underneath. -
Page 17: Removing The Main Control Card
Service Manual EDG 650.0 6.10 Removing the main control card Unplug all the connectors from the main control card. Using a pair of flat-nose pliers, carefully release the six fixing clips and remove the cover from the unit. Now withdraw the control card from its holder. -
Page 18: Renewing The Complete Heat Barrier Mat
Service Manual EDG 650.0 6.13 Renewing the complete barrier mat Remove the main control card. Do not disconnect the cables. Take out the reservoir and its bracket. Remove the upper air duct. Undo the 8 screws on the cooking compartment. -
Page 19: Removing The Flap
Service Manual EDG 650.0 6.14 Removing the door Open the door to its fullest extent. Insert pins (A) into the holes in the hinges. Push down both round buttons (B) on the door in front of the hinges. Press down on the hinges. -
Page 20: Fault Diagnosis
Service Manual EDG 650.0 Fault diagnosis Type of problem Water circulation problem The main elements in the oven stop working. A buzzer sounds and “E3” appears in the display instead of the time. 3 minutes after the fault occurs, the fan stops. - Page 21 Service Manual EDG 650.0 Reed Switch Test Open door Replace the reservoir Water level reading maximum Reed switch card, display or main card not working Press the PLUS button Probe Test P1 will be displayed Probe not working or not connected, main...
- Page 22 Service Manual EDG 650.0 Press PLUS button P4 will be displayed Generator Test Energy consumption 1425W<P<1525W Heating surface n.w. or not connected, main card not working Press PLUS button P5 will be displayed Heating Surface Test Energy consumption 355W<P<410W Heating surface n.w. or not...
- Page 23 Service Manual EDG 650.0 Button Test Start test Press COOK button COOK and TIME will be showing as 35 minutes Keypad not working or not connected Press “–“ button Time reduced Keypad not working or not connected Press “+“ button...
- Page 24 Service Manual EDG 650.0 Press the STOP button twice. Time display and the water level Keypad not working or not connected Press the <<SET>> button Default settings shown COOK Keypad not working or not connected End of test Remarks: You can exit the diagnosis utility program at any time by pressing the STOP button.
-
Page 25: Circuit Diagrams
Service Manual EDG 650.0 Circuit diagrams Circuit diagram For internal use only... - Page 26 Service Manual EDG 650.0 Circuit diagram For internal use only...
- Page 27 Service Manual EDG 650.0 Legend: Thermoactivator Terminal box Electronic card Pump Heating layer Door switch Stirrer motor Visual indicator Anti-parasitic filter Turbine Klixon Frontage heating element Oven switch Heating element For internal use only...
Need help?
Do you have a question about the EDG 650.0 and is the answer not in the manual?
Questions and answers