Subscribe to Our Youtube Channel
Related Manuals for Jung TK IS 14 Series
Summary of Contents for Jung TK IS 14 Series
- Page 1 Product Information DCM Comfort indoor station TK IS xx x14 x ALBRECHT JUNG GMBH & CO. KG Volmestraße 1 Phone +49.2355.806-0 E-Mail: mail.info@jung.de 58579 Schalksmühle Fax +49.2355.806-189 Internet: gb.jung.de...
-
Page 2: Table Of Contents
Table of content Information about this manual ..................... 3 Safety instructions....................... 3 Application / Brief description ....................4 Application ........................4 Brief description....................... 4 Device overview ........................5 Indication and operation ...................... 6 Wiring and installation ......................7 Wiring example........................ 7 Connecting diagram ...................... -
Page 3: Information About This Manual
Information about this manual On pages 35 and 36 you can read the "terms and definitions" of this manual. We recommend to read these explanation carefully before you start the adjustment of the indoor station. Safety instructions Assembly, installation, and commissioning must only be carried out by a qualified electrician! For work on systems with 230 V AC mains current the safety requirements of DIN VDE 0100 must be observed. -
Page 4: Application / Brief Description
Application / Brief description Application • acoustical and optical indication of front door and internal calls • hands-free communication with high audio quality (full duplex) • door release function • switching light • integrated frame for the design ranges AS 500, A creation and CD 500 Combination with other devices possible for the LS design ranges (up to 5-gang frames) and the Flat Design (up to 3-gang) Brief description... -
Page 5: Device Overview
Device overview Microphone Ring tone button / Volume Function button Loudspeaker Communication button Door release button LED indication Ring tone setting mode Ring tone on/off blue Operation LED Setting mode for function button Call diversion / Automatic door release active or internal call transmitted Voice memo LED green... -
Page 6: Indication And Operation
Indication and operation Ring tone button • Adjustment of ring tone volume • Ring tone deactivation • Adjustment of talking volume • Initiate setting mode for ring tones Indication • LED on = Ring tone deactivated LED red (b) • Start/end of hands free communication Communication •... -
Page 7: Wiring And Installation
Wiring and installation Wiring example Please observe cable length and loop resistance. Indoor station Floor bell button Indoor station Floor bell button Outdoor station Power supply & control unit Door release relay and illumination Connecting diagram... -
Page 8: Installation
Installation • Installation into flush wall boxes according to DIN 49 073. Do not paint or wallpaper over the supporting frame (1). • Connection as wiring example (page 7). Installation Reverse side of device Inscription for connection terminal Flush wall Label with serial number of the device 1 Supporting frame, 2 Wall box screws, 3 Design frame,... -
Page 9: Commissioning
Commissioning • Install all devices of the DCM system • Short-circuit test for a-, b- and P-wires • Switch on supply voltage Following functions should work without programming the indoor station: - Communication of indoor station with outdoor station - Door release function - Switching light •... -
Page 10: Function Button
Function button One function can be assigned to the function button. An additional function can be adjusted: • "automatic main door release" with additional function "automatic floor door release" or • automatic hands-free operation after internal call Internal call Preparation DCM system is in idle mode. -
Page 11: Call Diversion
Call diversion Preparation DCM system is in idle mode. Target indoor station (IS2): Push communication button. Starting setting mode at indoor station (IS1) • Push function button (for approx. 8 s) until you can hear acknowledge tone. • fast LED flashing release the function button fast LED flashing •... -
Page 12: Automatic Door Release
Automatic door release Preparation DCM system is in idle mode. • Push function button (for approx. 8 s) until you can hear acknowledge tone. • fast LED flashing release the function button fast LED flashing • Push function button at TOP section •... -
Page 13: Light Switching
Light switching Resetting the function button to the function „light switching“ takes place by means of re- loading the factory settings. Reloading the factory settings Attention ! All settings are reset to factory settings. • Push ring tone button and function button (for approx. -
Page 14: Adjusting The Function Button With The Service Device
Adjusting the function button with the service device The initiation starts always with the key combination *95#Ser.-Nr.# . Initiation Call diversion Automatic door release Internal call Control function 8 Parallel function Example: Outdoor station Floor door bell button IS (228515) is assigned to a bell button of the outdoor station. IS (228520) will be parallel assigned to the IS (228515). -
Page 15: Additional Functions
Additional functions One of the following functions can be additionally adjusted: • Automatically hands-free operation after internal call • Automatic floor door release, control function 11 Automatically hands-free operation after internal call When an indoor station receives an internal call, an automatically hands-free operation will be activated. -
Page 16: Automatic Floor Door Release, Control Function 11
Automatic floor door release, control function 11 When the function button is adjusted with the function automatic door release (e.g. for the main entrance door in a clinic centre) then the additional control function 11 involves an- other door release relay (e.g. for the floor entrance door of the clinic centre). This relay will be activated by means of pushing the floor bell button. -
Page 17: Settings
Settings Signs and symbols acknowledge tone ring tone slow LED flashing: 0.5 s ON / 0.5 s OFF fast LED flashing: 0.125 s ON / 0.125 s OFF LED illuminated LED pulse flashing: 0.5 s ON / 1.5 s OFF LED OFF short centrically pushing of button short pushing of button section... -
Page 18: Voice Volume
Voice volume Preparation The indoor station must be in talking mode. 8 voice volume levels can be adjusted: Increase voice volume • Push ring tone button at the TOP section (for approx. 1 s). • the voice volume increases Decrease voice volume •... -
Page 19: Volume Of Voice Memo Recorder
Volume of voice memo recorder Preparation Start the voice memo (see Voice memo function: , page 8 voice volume levels can be adjusted: Increase voice volume • Push ring tone button at the TOP section (for approx. 1 s). • the voice volume increases Decrease voice volume •... -
Page 20: Ring Tone Off / On
Ring tone OFF / ON Preparation DCM system is in idle mode. Ring tone OFF • Push ring tone button LEFT or RIGHT. The LED is illuminated, the ring tone is OFF. Ring tone ON • Push ring tone button LEFT or RIGHT. •... -
Page 21: Ring Tone Selection
Ring tone selection Various outdoor station can be installed into a DCM system, e.g. in buildings with various entrances. At the indoor station you can assign 2 different ring tones for the entrances. The first ring tone can be assigned to the main outdoor station. The second ring tone can be assigned to all other connected outdoor station. -
Page 22: Ring Tone 2 (For Outdoor Station > 0)
Ring tone 2 (for Outdoor station > 0) Preparation DCM system is in idle mode. • Push ring tone button (for approx. 8 s) until you can hear acknowledge tone. • fast LED flashing Release the ring tone button. The TOP LED of the ring tone button flashes fast. •... -
Page 23: Ring Tone For Internal Call
Ring tone for internal call Preparation DCM system is in idle mode. • Push ring tone button (for approx. 8 s) until you can hear acknowledge tone. • fast LED flashing Release the ring tone button. The TOP LED of the ring tone button flashes fast. •... -
Page 24: Ring Tone For Floor Bell Button
Ring tone for floor bell button Preparation DCM system is in idle mode. • Push ring tone button (for approx. 8 s) until you can hear acknowledge tone. • fast LED flashing Release the ring tone button. The TOP LED of the ring tone button flashes fast. •... -
Page 25: Ring Tone Selection For Sub Door Call
Ring tone selection for sub door call Note: The assignment of a sub door call at the outdoor station is only possible with the ser- vice device (see product information of TK-SERVICE). Start setting mode Preparation DCM system is in idle mode. •... - Page 26 Selection sub door call 3 (Serial-no.+3) LED pulse flashing • Push ring tone button at the LEFT section. • You can hear the next ring tone. Now this ring tone is selected for the sub door call 3 Repeat the action until the desired ring tone is selected.
-
Page 27: Operation
Operation Start communication, door release, switching light Start communication after incoming call (Door call or internal call) • Incoming call You can hear the selected ring tone and the green LED of the communication button flashes. • Push the communication button to start the connection (max. - Page 28 Door release • Push the door release button to open the door. When light switching function* is activated: • Push communication button • Push the door release button to open the door. Light switching • Push the function button, when function button is ad- justed with light switching (factory setting).
- Page 29 Features of the function button Short push of the function button (max. 1 s). Depending on the set function the indoor station indi- cates the action with visual or acoustic signals: Light switching Internal call flashing Call diversion ON Call diversion OFF Automatic door release ON Automatic door release OFF Automatic floor door release function...
-
Page 30: Record, Play Or Delete A Ring Tone
Record, play or delete a ring tone You can record a sound or ring tone with the microphone of the indoor station. The max. recording time is approx. 3 s. After recording the new ring tone / sound has to be selected as a new ring tone (see "ring tone selection"). - Page 31 Play recorded ring tone Preparation DCM system is in idle mode. • Push ring tone button (for approx. 8 s) until you can hear acknowledge tone. • fast LED flashing release the ring tone button Fast flashing of the TOP LED of ring tone button. •...
- Page 32 Delete the recorded ring tone Preparation DCM system is in idle mode. • Push ring tone button until you can hear acknowledge tone (after 8 s). • fast LED flashing release the ring tone button Fast flashing of the TOP LED of ring tone button. •...
-
Page 33: Voice Memo Function: Record, Play And Delete Message
Voice memo function: Record, play and delete message You can record a voice memo with the microphone of the indoor station. The max. re- cording time is approx. 30 s. After recording, the new voice memo will be indicated by means of the flashing LED. - Page 34 Play voice memo Slow LED flashing: The LED indicates a new voice memo. The LED flashes until you play the memo. • Push communication button until you can hear acknowledge tone(after 4 s). • release the communication button • The voice memo will be played. After you played the voice memo, the LED turns off.
-
Page 35: Explanation Of Terms And Definitions
Explanation of terms and definitions AS-address Every outdoor station is assigned with an outdoor station address. The address enables the differentiation between the various in- stalled outdoor station. Selective communication or door release of e.g. main- or side entrance can be realised. Ready for operation Incoming door call - You can hear a ring tone and the LED at the communication button flashes. - Page 36 Talking mode A communication between indoor and outdoor station will be acti- vated by means of pushing the communication button. Die LED of the communication button is illuminated. The LED of the communication button is flashing, when another in- door station is already communicating with the outdoor station. After elapsed talking time, activating the door release or pushing the communication button again, the device turns back into idle mode.
-
Page 37: General Notes On The Wiring In Dcm Audio Systems
General notes on the wiring in DCM audio systems The cabling depends on the building situation and is only limited by its length. • When selecting the cable length consider: the loop resistance must not exceed max. 20 Ω (table) •... -
Page 38: Technical Data
Principle of loop resistance Measuring loop resistance Rule: Rule: No door communication device shall have a longer Turn OFF 230 V / 50 Hz of the VS. distance from the power supply & control unit than Connect a and b short circuit at the VS. 20 Ohm ! All other devices do not disturb the measuring proc- ess and remain connected. -
Page 39: Acceptance Of Guarantee
We accept the guarantee in accordance with the corresponding legal provisions. Please return the unit postage paid to our central service department giving a brief description of the fault: ALBRECHT JUNG GMBH & CO. KG Technique (DCM) Service-Line: 0 23 55 . 80 65 52 Service-Centre Kupferstr.
Need help?
Do you have a question about the TK IS 14 Series and is the answer not in the manual?
Questions and answers