Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MAKINEX VS-125-US
Summary of Contents for MAKINEX VS-125-US
- Page 1 Vinyl Stripper VS-125/ VS-125-US OPERATOR’S MANUAL Rev0919...
-
Page 2: Table Of Contents
SAFETY DECALS ..............................4 PRODUCT DESCRIPTION AND SPECIFICATIONS .............. 5 INSTRUCTIONS FOR USE ..................... 7 SETTING UP THE MAKINEX VS-125 VINYL STRIPPER ..................7 OPERATING THE MAKINEX VS-125 VINYL STRIPPER ................... 11 VINYL STRIPPER DOES NOT START ....................... 12 TRANSPORTING AND STORING ........................12 MAINTENANCE ........................ -
Page 3: Introduction
Thank you for purchasing a MAKINEX product. This manual provides information and procedures to safely operate and maintain the VS- 125/ VS-125-US Vinyl Stripper. For your own safety and protection from injury, carefully read, understand, and observe the safety instructions described in this manual. -
Page 4: About This Manual
This manual is designed to provide the user with the information required to operate and maintain the ‘VS-125/ VS-125-US’ Vinyl Stripper correctly and safely. The following safety symbols are used with a key word to alert you to potential hazards in operating and owning power equipment. -
Page 5: Safety Information
SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS Throughout this document there are several safety warnings. The user should read through this complete document before using the MAKINEX VS-125/ VS-125-US. Ensure you read all information contained in this manual before using READ the MAKINEX VS-125/ VS-125-US. -
Page 6: Safety Decals
SAFETY DECALS There are several stickers on the MAKINEX VS-125/ VS-125-US machine that have been provided to alert the user of potential safety risks/hazards. Please read and adhere to all instructions on the Unit. It is forbidden to remove any safety or instructional stickers or panels from the MAKINEX VS-125/ VS-125-US. -
Page 7: Product Description And Specifications
The MAKINEX VS-125 is a world-class electric floor-stripping machine used extensively in the construction and hire industry to remove coverings such as vinyl, cork and tiles from floor surfaces. MAKINEX VS-125/ VS-125-US is solid and reliable, featuring tool-free set-up, quiet operation, and minimum ongoing maintenance. MAKINEX VS-125/ VS-125-US Specifications... - Page 8 OVERALL MACHINE DIMENSIONS 370mm 812mm 14.57” 31.97” Floor Stripper – User Manual (Rev0919) Page 6 of 17...
-
Page 9: Instructions For Use
INSTRUCTIONS FOR USE Do not operate the MAKINEX VS-125/ VS-125-US without wearing the appropriate personal protective equipment and assessing the surrounding area for hazards. WARNING Read and adhere to all safety and operation instructions. WARNING SETTING UP THE MAKINEX VS-125/ VS-125-US VINYL STRIPPER When setting up, ensure the Vinyl Stripper is OFF and the power cord is unplugged. - Page 10 4. Align the hole of the metal plate with the hole 5. Twist in the threaded handle slowly and softly to of the Vinyl Stripper, on the underside of the ensure it goes into the threads of the metal plate. square tube.
- Page 11 Blade Orientation, Preparation and Installation Do not insert or remove the blade with the electrical cord plugged in. WARNING FOR CONCRETE FLOORS: Extend the blade approximately 20mm (4/5in) with the bevel facing up. FOR TIMBER FLOORS: Extend the blade approximately 50mm (2in) with the bevel facing the READ CAREFULLY...
- Page 12 2. Installation of the blade: 5” Blade Ensure the machine is unplugged and tilt back onto the control handles. WARNING 2. Slide the blade through the gap and in between the two bolts until it hits the back 1. Turn the handles to loosen the bottom stop.
-
Page 13: Operating The Makinex Vs-125 Vinyl Stripper
OPERATING THE MAKINEX VS-125/ VS-125-US VINYL STRIPPER Do not cut the power cord. DANGER Before turning the machine on, make sure it is clear from the walls, humans, pets and other objects and obstructions. WARNING 1. Tilt the Vinyl Stripper is slightly upright where the stripping blade is off the floor surface. -
Page 14: Vinyl Stripper Does Not Start
VINYL STRIPPER DOES NOT START During operation, if the unit suddenly shuts down and does not start when it is ON, the motor overloaded and the circuit breaker was tripped. To reset the circuit breaker, do the following. Identify the Push Circuit Breaker location, underneath the unit. -
Page 15: Maintenance
MAINTENANCE Each MAKINEX VS-125/ VS-125-US machine has been individually checked after manufacture to the highest standard. However, it is important to follow the service procedures before each use, in order to prolong the life of this product and protect the warranty conditions that apply. -
Page 16: Limited One Year Warranty
(contained in relevant owner’s manual supplied with this product), by an authorised MAKINEX dealer or MAKINEX service technician. You are free to have your MAKINEX product serviced by any suitably qualified mechanic or electrician (depending on the mechanical or electrical... -
Page 17: Warranty Exclusions
WARRANTY EXCLUSIONS This warranty does not cover the following repairs and equipment: NORMAL WEAR The Vinyl Stripper needs periodic service and genuine parts to perform well. This warranty does not cover repair when normal use has exhausted the life of a consumable part for example the oil filter and fuel filter. -
Page 18: Owner's Responsibility Under Limited Warranty
(parts & labour), or replace the machine under warranty. • All warranties will be carried out by MAKINEX authorised staff or appointed agents at a premises to be determined by the Manufacturer. • It is the responsibility (and cost) of MAKINEX or our appointed agent to return the machine to be repaired or replaced under warranty to the consumer- this is valid for domestic territories only (e.g. -
Page 19: Contact Information
CONTACT INFORMATION For sales, service, warranty and parts for all MAKINEX products; please refer below. SALES, SERVICE, SPARE PARTS & WARRANTY SALES TEL 1300 795 953 or +61 2 9460 8071 WEB www.makinex.com.au AUSTRALIA SERVICE, SPARE PARTS & WARRANTY EMAIL service@makinex.com.au...
Need help?
Do you have a question about the VS-125-US and is the answer not in the manual?
Questions and answers