Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MAKINEX Hose2Go
Summary of Contents for MAKINEX Hose2Go
- Page 1 Hose2Go Pressurised Water Supply Unit OPERATOR’S MANUAL Rev 0919...
-
Page 2: Table Of Contents
PRODUCT DESCRIPTION AND SPECIFICATIONS ............4 OPERATION ........................6 BEFORE USE........................6 MAINTENANCE ........................8 GENERAL RECOMMENDATIONS ..................8 HOSE2GO SPECIFIC MAINTENANCE ................8 STORAGE ..........................9 TROUBLESHOOTING ......................10 LIMITED WARRANTY ......................11 WARRANTY: (Ex-factory/ Reseller premise) ..............11 WARRANTY EXCLUSIONS .................... -
Page 3: Table Of Contents
DISCLAIMER MAKINEX and its affiliates take no responsibility for any damage, injury or death resulting from the incorrect or unsafe use of this product. Use of this product should be undertaken by competent persons only. It is the operator’s responsibility to ensure that the following safety procedures are followed. -
Page 4: About This Manual
This manual uses the following symbols to help differentiate between different kinds of information. The safety symbol is used with a key word to alert you to potential hazards in operating and owning Hose2Go. Follow all safety messages to avoid or reduce the risk of serious injury or death. -
Page 5: Product Information
• ALWAYS wear PPE appropriate to task; such as goggles, ear muffs, gloves, and closed foot wear. • ALWAYS use Makinex branded hose fittings as they are tested at rated pressure. Use of non-genuine accessories may reduce performance and/or working life of device. -
Page 6: Safety Decals
• Be aware of electrical hazards whilst performing task as contact WARNING with power source may cause electric shock. SAFETY DECALS Serial # Decal (On side) (Concealed in base) Do not attempt to (At rear also) disassemble HOSE2GO – USER MANUAL Page 4 of 14... -
Page 7: Product Description And Specifications
PRODUCT DESCRIPTION AND SPECIFICATIONS The MAKINEX Hose2Go is a pressurised water supply device. It is designed and engineered to simplify the process of supplying water in situations where regular hosing is difficult. The Hose2Go includes a multi-function nozzle, an on/off valve, 3 metres of reinforced hose, all mounted on a compact two chamber frame design. -
Page 8: Operation
2. Ensure all fittings are tight (do not over tighten using tools as damage may occur to fittings). NOTE: IMPROPER treatment of Hose2Go can damage it and shorten its working life. DO NOT attempt to open device to alter or to repair it. This must ONLY be done by Makinex approved service technician. - Page 9 HOSE2GO – USER MANUAL Page 7 of 14...
-
Page 10: Maintenance
Before use, clear debris from hose line. If debris has entered the hose line disconnect from Hose2Go base (be aware that if the device is full water will spray out) and connect the free hose to a tap, flush out any debris before reconnecting and refilling Hose2Go Check multi spray nozzle Ensure nozzle is connected securely and functioning correctly. -
Page 11: Storage
STORAGE Long term storage instructions It is not advised to store a full Hose2Go for long periods (weeks/months) as this may reduce performance of your product. Empty your Hose2Go before long-term storage. DO NOT clean inside tanks with soaps or other cleaning agents/products, rinse with fresh water and empty. -
Page 12: Troubleshooting
TROUBLE SHOOTING GUIDE PROBLEM CAUSE REMEDY Valve faulty Inspect valve on hose Remove hose from Hose2Go and flush with tap water from either end Blockage in hose Check for blockages at barbed fittings Pump does not fill Blockage in top cap Inspect inlet for debris Refer to applicable machine’s... -
Page 13: Limited Warranty
Installation, Use and Maintenance This warranty will not apply to parts and/or labour if this Hose2Go is deemed to have been misused, neglected, involved in an accident, abused, loaded beyond the Hose2Go’s limits, modified, installed improperly or connected incorrectly to any water supply. Normal maintenance such as cleaning, adjustments to fittings, obstruction due to build-up is not covered by this warranty. -
Page 14: Responsibility Of The Consumer Under This Limited Warranty
• It is the responsibility (and cost) of MAKINEX or our appointed agent to return the device to be repaired or replaced under warranty to the consumer- this is valid for domestic territories only (e.g. Australian units will be delivered within Australian territory, USA units will be delivered within USA territory and European units will be delivered within its designated country’s territories). -
Page 15: Contact Information
CONTACT INFORMATION For sales, service, warranty and parts for all MAKINEX products; please refer below. SALES, SERVICE, SPARE PARTS & WARRANTY SALES TEL 1300 795 953 or +61 2 9460 8071 AUSTRALIA WEB www.makinex.com.au SERVICE, SPARE PARTS & WARRANTY EMAIL service@makinex.com.au... - Page 16 HOSE2GO – USER MANUAL Page 14 of 14...
Need help?
Do you have a question about the Hose2Go and is the answer not in the manual?
Questions and answers