Table of Contents
Related Manuals for Hameg HM6050-2
Summary of Contents for Hameg HM6050-2
- Page 1 S t a b i l i z a t i o n N e t w o r k H M 6 0 5 0 - 2 Manual 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.TestEquipmentDepot.com Hameg HM6050-2D Shown...
-
Page 2: Table Of Contents
Operating conditions ..............Warranty and repair ............... Operating controls of the HM6050-2 ........Rear panel ..................Safety hints ..................RS-232 Interface ................RS-232 Commands ............... Setting into operation ..............EMC measurement procedures for LISN HM6050-2 ....Subject to change without notice... -
Page 3: General Information Regarding The Ce Marking
HAMEG instruments fulfill the regulations of the EMC directive. The conformity test made by HAMEG is based on the actual generic- and product standards. In cases where different limit values are applicable, HAMEG applies the severer standard. For emission the limits for residential, commercial and light industry are applied. -
Page 4: Declaration Of Conformity
D - 63533 Mainhausen Nombre y dirección del fabricante Die HAMEG GmbH / HAMEG S.a.r.l bescheinigt die Konformität für das Produkt The HAMEG GmbH / HAMEG S.a.r.l herewith declares conformity of the product HAMEG GmbH / HAMEG S.a.r.l déclare la conformite du produit La empresa HAMEG GmbH / HAMEG S.a.r.l. -
Page 5: Line Impedance Stabilization Network Hm6050-2
LISN together with a Spectrum Analyzer/EMC between the signals, the selected one will Receiver. The DUT (device under test) must be available at the HM6050-2’s test signal be connected directly to the LISN. Inside the outlet. The stabilization network (simulation... -
Page 6: Specifications
Specifications HM6050-2 Frequency range: 9 kHz to 30 MHz Network inductance: Z = 50 II (50 µH + 5 ) error < 20% acc. to VDE 0876T1 Max. current: 2 x 16 A continuous Voltage: 230 V~ at 50/60 Hz... -
Page 7: Operating Manual
Safety Class 1 regulations. To put the HM6050-2 to operation it has to be connected to an AC power outlet (with protective ground) according to VDE-0100. Due to the relative high leakage current (ca. 800 mA) the equip- ment cannot be operated in combination with a leakage current circuit breaker. -
Page 8: Replacement Of Fuses
Replacement of fuses The internal power supply unit of the HM6050-2 contains a fuse. Ex factory the HM6050-2 is set to 230V ±10% (50-60Hz). If the instrument shall operate at a mains voltage of 115 V ±10%, the wire bridges have to be changed by soldering. -
Page 9: Operating Conditions
HAMEG customer service for repairs and spare parts. Return Material Authorization (RMA): Before sending back your instrument to HAMEG do apply for a RMA number either by fax or on the Internet: http://www.hameg.de. If you do not have suitable packaging for the instrument on hand please contact the HAMAG sales department (Tel.: +49 (0) 6182/800 300,... -
Page 10: Operating Controls Of The Hm6050-2
AC power cable. (3) Mains power outlet for the DUT The DUT will be connected to the HM6050-2’s Mains power outlet with its AC power cable. The maximum supply current of the DUT must not exceed a continuous current of 16 A at an ambient temperature of 23 °C. - Page 11 (11) Test Receiver (test signal output) The output impedance Z of the HM6050-2’s test signal output is 50 . The shielding connection of the BNC jack is connected to the housing and thus to ground. A two plug broadband BNC cable is used to attach the HM6050-2 to a Test Receiver or Spectrum Analyzer.
-
Page 12: Rear Panel
Rear panel (14) AC power cable The power cable is used to attach the HM6050-2 to the mains outlet. ( See: “Setting into operation” ). (15) Ground block The ground block is made of aluminum and fastened to the backside of the housing by two screws (below the mains cable outlet). -
Page 13: Rs-232 Interface
Read the operator’s manual before setting up the HM6050-2! Only qualified personnel are allowed to set up the LISN for operation. HM6050-2 has been designed in conformity to regulations VDE 9876 and CISPR Publ. 16. The leakage current of the instrument exceeds the allowed value of 0.5 mA... -
Page 14: Emc Measurement Procedures For Lisn Hm6050-2
IEC364-4-41 (CENELEC HD 384.4.41 and VDE 0100 Part 410). Due to the circuitry of the HM6050-2 a maximum leakage current of 800 mA can occur. It is not possible to operate the HM6050-2 at a mains outlet with a leakage current circuit breaker. Attention! Danger of death! The LISN has to be grounded according to the regulations (Cenelec HD384/DIN VDE0100) separately;...