Advertisement
5.
OPERATION
5.0
Before first use lubricate the tool with synthetic pneumatic oil , applied into the connector at the base of the handle
WARNING! The boot tool is designed for the installation of flexible rubber CV boots only and should be used with no other products
#
and for no other purpose.
WARNING! The boot tool should only be used with flexible rubber boots which conform to the following specification.
#
Elongation at break: Minimum 600 %
Tensile strength: Minimum 30 N/mm²
Hardness: Maximum 50 Shore A
Boots which do not conform to this specification may tear.
5.1
Adjust the air compressor to give a maximum pressure of 9 bar (125 psi) at its outlet.
5.2
Before connecting the air line to the boot tool put the flexible rubber boot over the boot tool arms. Make sure that the ends of the arms
are projecting from the top opening of the rubber boot (Fig.A).
5.3
Connect the air line to the air connector at the end of the handle (Fig.B).
When operating the boot tool, to open the tool "arms", orientate the unit downwards, at an angle of 45 degrees.
5.4
Activate the splaying of the boot tool arms by pressing the red button on the handle, thus alowing air to enter the device (Fig.C).
5.5
When the arms have stretched the boot by the desired amount, release the red button in order to prevent the arms
opening any further (Fig.D).
5.6
Manoeuvre the opened tool and boot over the end of the drive shaft until it is in the required place (Fig.E).
5.7
To release the air pressure in the boot tool, press the yellow button on the reverse side of the handle (Fig.F). As the air pressure is
released the arms will close down onto the drive shaft.
5.8
Disconnect the air supply (Fig.G).
5.9
Place one hand onto the rubber boot to hold it in place (Fig.H).
5.10 Finally, entirely withdraw the tool from the boot (Fig.I). Do not leave the Boot Tool under air pressure when not in use.
5.11 A purpose designed safety holder for storing the boot tool when not in use is available as an optional extra. (Part No. LM77200)
6.
MAINTENANCE
6.1
Before first use and regularly thereafter, lubricate the tool with synthetic pneumatic oil , in the connector at the base . (the air pressure
will distribute this eventually inside the tool).
6.2
Damage caused due to incorrect assembly, maintenance or not regularly lubricating the device, will void the warranty.
7.
DECLARATION OF CONFORMITY
Declaration of Conformity
CV Joint Boot Tools
Model Nos: BSL100.V2, BSL101
98/37/EC Machinery Directive
93/68/EEC CE Marking Directive
EN ISO 12100-1: 2003, EN ISO 12100-2: 2003
EN1050: 1997, EN 983: 1996, EN 792-2: 2000
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
We, the sole importer into the UK, declare that the products listed below are in conformity with the following standards and directives
Signed by Tim Thompson
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products.
The construction files for these products are held by the Manufacturer and may be
inspected on request by contacting Jack Sealey Ltd.
01284 757500
01284 703534
17th August 2007
www.sealey.co.uk
Web
sales@sealey.co.uk
email
BSL100.V2, BSL101 - 3 - 170807
Advertisement
