Advertisement
Operating Instructions and Parts Manual
WARNING: DO NOT use this equipment with gasoline or other
flammable liquids or with fluids at temperatures above 175° Fahrenheit
(80° Celsius). Keep away from open flames or excessive heat.
INSTRUCTIONS
COLLECTING WASTE OIL
1. Position the Waste Oil Drain under the vehicle, adjust the bowl to the
desired height, and set the brakes on the casters.
2. Check the sight glass to ensure there is sufficient remaining capacity.
Never allow fluid to exceed the maximum level. The reservoir will not
drain if the fluid exceeds the maximum level on the sight glass.
DRAINING THE RESERVOIR
1. Raise the collecting bowl to its maximum height and set the caster
brakes. Close the pressure valve on the side of the Drain Tube.
WARNING: If valve is not closed, waste oil will shoot out of the
funnel and spray the user.
2. Secure the discharge hose to the bulk waste oil tank and open the
discharge hose valve.
3. Set the air supply to a maximum of 7 PSI (0.5 Bar).
OEMTOOLS™ ONE YEAR WARRANTY
For up to one year from the date of purchase of this OEMTOOLS™ product, if you find any defect in material or workmanship (through normal
usage), return it to the place of purchase or to OEMTOOLS™ for repair or replacement at our discretion. In order to obtain this service, send the
product and proof of purchase (transportation pre-paid) to:
OEMTOOLS™ Q.A. Dept, 3580 E. Raines Road #3, Memphis, TN 38118.
We will not be responsible for lost or damaged goods during transportation; please insure your package. If our inspection verifies the defect,
we will either repair or replace the product, or we may elect to refund the purchase price if we cannot readily and quickly provide you with a
replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not
within the scope of our warranty, then you must bear the cost of returning the product.
OEMTOOLS™ does not provide warranty for products labeled other than OEM
for products subjected to abnormal use. Abnormal use includes (but is not limited to) abuse, accident, alteration, neglect, and unauthorized
or unreasonable use or repairs. This warranty does not cover bits, blades, files, batteries, or calibration. We recommend that you maintain
your tools and sharpen or replace blades, bits, files, and batteries as necessary. OEMTOOLS™ reserves the right to make any changes in
construction or design at any time without any obligation in incorporating such changes to tools or equipment previously sold.
OEMTOOLS™ makes every effort to ensure that its products meet high quality and durability standards, and warrants to the original purchaser
that this product is free from defects in materials and workmanship for the period of one year from the date of purchase. This warranty does not
apply to damage due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising
from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may also have other rights, which vary
from state to state.
Don't forget to register your new OEMTOOLS™ product at www.oem-tools.com.
12/18
2018 OEMTOOLS
™
4. Connect air supply to the valve stem using the air chuck tire
5. Remove the air chuck from the valve stem when the desired flow
NOTE: If flow rate stops before the drain is empty, repeat steps 3, 4, and 5.
MAINTENANCE
1. Relieve pressure or vacuum before inspecting or servicing.
2. Always store the Waste Oil Drain in a well-protected area where it
3. Keep the Waste Oil Drain clean for better and safer performance.
4. Inspect the Reservoir, Hoses, Caps, Gaskets, Seals, and Gauge
CONTACT US
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: 1-866-458-2472
www.oem-tools.com
4
WASTE OIL DRAIN
WARNING: DO NOT exceed 7 PSI (0.5 Bar). Failure to comply
may result in serious personal injury.
inflator.
rate is achieved or if the safety relief valve opens.
will not be exposed to inclement weather, corrosive vapors, abrasive
dust, or any other harmful elements.
periodically and, if damaged, replace them.
or OEMTOOLS™. OEMTOOLS™ will not provide any warranty
®
24861
Advertisement
