Related Manuals for Macab DT-1700
Summary of Contents for Macab DT-1700
- Page 1 MANUAL ENG-1 • 050223 • 50009-2 DT-1700 Also contains • Menu opttions and data for built-in modulator • Data for broadband amplifier QPSK – NDS...
-
Page 2: Table Of Contents
• Always carry out a new channel search after downloading new software • Make sure that the power cable is easily accessible in case the power supply to the receiver has to be switched off • The latest software and information can be downloaded from www.macab.com/helpdesk ”Download” Innehåll DT-1700 ..........2 PID setting ........ -
Page 3: Front
MANUAL DT-1700 Front Fan** Buttons* - Menu Display - Enter - Right - Left - Up - Down Programming buttons* Card reader On indication = green LED QPSK-lock = yellow LED Alarm = red LED Reset-button RS232 connection Only for service ** A temperature-controlled fan is situated on top of the receiver. -
Page 4: Back
( 180–250 V AC ) * The DC out connector must only be used for the specially adapted broadband amplifier. RF ( In ) Not utilised RF (In) connector must be terminated with 75 Ω . RF ( Ut ) DT-1700 with built-in modulator... -
Page 5: Smartcard
PROGRAMME CARD CARD READER* * embedded NDS DT-1700 is equipped with a card reader for the downloaded (embedded) coding system. CARD READER Insert the programme card with the gold-coloured contact surface facing to the right, as shown on the label on the front of the receiver. The alarm lamp will remain on until an updated programme card is inserted, when it will automatically switch off. -
Page 6: Knappar För Programmering
2 seconds. The DT-1700 is programmed using the Menu, Enter, Up, Down, Right and Left buttons and the display. In order to programme the digital receiver correctly, it must be switched on and receiving a satellite signal. -
Page 7: Menu Overview
MANUAL DT-1700 Menu overview For Information press Right button Once Twice 3 times 4 times 5 times 6 times 7 times 8 times 9 times 10 times 11 times OUT LVL BOXINFO DISABLE 16/9 PROGRAMMING 1) Press Menu button 2) Select IF frequency... -
Page 8: Programmering
Programming All programming is carried out using the display and the buttons on the front of the DT-1700. When the receiver is in use, the buttons on the front are locked by a button lock. This is shown by a symbol in the upper left-hand corner of the... - Page 9 Continue on page 11 if the modulator has not been installed. BUILT-IN MODULATOR When the built-in modulator has been installed in the DT-1700 the following menu options will be automatically activated. They are marked (Modulator) and are shown in the display during programming.
- Page 10 MANUAL DT-1700 DEPTH (Modulator) Select modulator depth, available settings 72,5–90. Recommended setting (75%) Use the Up/Down buttons to select modulator depth. MAIN MENU MODULATOR ENTER Press the Enter button to move to the next menu option. DEPTH. SND SUB (Modulator) Select transmission system BG, I, DK, MN.
- Page 11 MANUAL DT-1700 PISNDRAT (Modulator) Select picture to sound ratio, available settings 11–18dB. Recommended setting (–15). Use the Up/Down buttons to select desired picture to sound ratio. MAIN MENU MODULATOR ENTER Press the Enter button to move to the next menu option.
- Page 12 CHANGING CHANNEL Changing to another channel within the transponder can easily be done using the buttons on the front of the DT-1700. De-activate by pressing the MENU and ENTER buttons at the same time for approximately 2 seconds Press the Left button.
- Page 13 MANUAL DT-1700 Information All information is monitored from the DT-1700 display except card information, which is shown on the TV screen. De-activate the button lock by pressing the MENU and ENTER buttons at the same time for approximately 2 seconds.
-
Page 14: Information "Menu
MANUAL DT-1700 LOG FILE A log file is created in connection with any errors. A number of different types of error can be logged in the file, see page 19. Press the Right button twice. VIEW LOG ENTER Press the Enter button. Use the Up/Down buttons to move within 1 ENTRIES the log file. - Page 15 MANUAL DT-1700 CARD INFORMATION When card information is activated, a menu will be displayed on the TV screen and different options can be chosen. Press the Right button four times. CA CONTROL CARD OK ENTER Press the Enter button and after a few seconds the menu will appear on the TV screen.
- Page 16 MANUAL DT-1700 OUT LVL (Modulator) The output level can be set to 0–99 which gives between 60–80dBµV. Press the Right button six times. MODULATOR Use the Up/Down buttons to specify a number. OUT. LVL Use the Left/Right buttons to move between the numbers.
- Page 17 MANUAL DT-1700 SUBTITLE ”position” There are six settings for the subtitle position (upwards/downwards) from 0 to 5. (Factory setting 2) Press Right button nine times. SUBTITLE Use the Up/Down buttons to select the required position. POSITION Press the Right button to move to the next menu option.
-
Page 18: Pid Setting
MANUAL DT-1700 PID setting PID setting is only to be used by advanced users if the auto search function fails. To set the V-PID, A-PID, PCR-PID and Text-PID, the PID tables in the channel lists must be converted into HEX. -
Page 19: Error Log
MANUAL DT-1700 Error log ERROR LOG Displays the number of the error in question in the log file. 100:03 Time N/A QPSK LOCK ERROR LOG Displays the reason for the error, showing number and text, see below. 100:03 Time N/A QPSK LOCK Some errors are displayed showing time and date of occurrence. -
Page 20: Technical Data Dt-1700
MANUAL DT-1700 Technical data DIGITAL SATELLITE RECEIVER DT-1700 Front End-DVB QPSK Demodulator Frequency range (MHz) 920–2150 Symbol rates (MS/s) 2 to 40 LNB power and control (V DC) 13/18 (350 mA) LNB control (KHz) 22 on/off Input level (dBµV) 50 to 80... -
Page 21: Built-In Modulator
MANUAL DT-1700 Built-in modulator (stereo) The modulator is built-in and adapted to DT-1700 at delivery. It cannot be mounted afterwards. RF ( In ) Not utilised RF (In) connector must be terminated with 75 Ω . RF ( Out ) -
Page 22: Broadband Amplifier
MANUAL DT-1700 Broadband amplifier RF in DC in (18,5–20V) from DC out on DT-1700 Changeover switch MATV for band selection RF out Output attenuator (0–15dB) Test socket (–30dB) The amlifier can be changed over into three modes depending on the band which will be used. -
Page 23: Frequency "Ccir
MANUAL DT-1700 CCIR-channels 48.25 231.25 423.25 K38 607.25 K64 815.25 238.25 K39 615.25 55.25 431.25 K65 823.25 62.25 245.25 439.25 K40 623.25 K66 831.25 252.25 447.25 631.25 839.25 259.25 455.25 K42 639.25 K68 847.25 105.25 266.25 463.25 K43 647.25 K69 855.25 112.25... - Page 24 Prod.nr: 9270058 Macab AB (publ) vannhögsgatan 7, S-231 66 trelleborg. tel: +46 410 36 36 00 fax: +46 410 36 36 01. e -mail: info@macab.se – www.macab.com...