DKS 2332-080 Quick Manual

900 MHz WIRELESS DUAL BAND REPEATER
The 900 MHz wireless dual band repeater (DBR) extends the wireless communication range between an access control system (900 MHz wireless
baseboard) and 900 MHz wireless tracker expansion board. It gets installed between the wireless devices that are too far or obstructed from each
other to reliably communicate with each other. It will receive a signal sent to it and repeat that signal to the next wireless device. ONLY 1 DBR can
be used in the same communication line of a tracker expansion board. The signal range of a DBR is Up to 1500 ft direct-line-of-sight with no
signal interference. See "900 MHz Wireless Baseboard Manual" for complete access control system wireless setup information.
Installation
Up to 1500 ft
Base Side
900 MHz
Wireless
Baseboard
A
1 2 3
4 5 6
Z
7 8 9
Example:
0
CALL
The wireless
baseboard
MUST be set to:
NET ID: 2A CH: 1
Base side communicates with the
wireless Baseboard of the 1830
series. The CH and NET ID of the
Base side MUST match the CH and
Net ID of the Baseboard.
DO NOT set Base side the same as
the Remote side.
Antenna
1/2" thick wall
PVC conduit
recommended
(not supplied).
Metal conduit
may interfere
with wireless
signal.
IMPORTANT:
Install the DBR
so the antenna is in a
location that is NOT
surrounded by metal
and is in free air as
high as possible above
the ground. Minimum
15 ft above ground
recommended.
Note: DoorKing offers a 900 MHz Wireless Test Range Kit (P/N 1514-140) to allow easy testing of the wireless signal between
2 devices at chosen locations BEFORE installing the devices. The self-powered test kit measures the 900 MHz wireless signal
between 2 devices in ANY chosen locations. Ensuring a good signal can be achieved before installation occurs.
2332-065 Issued 11-18
Version E
TIP: It is best to keep the CHs at least 2 numbers away from
each other if possible for signal separation. This helps
eliminate interference between base side and remote side.
NET ID: 2A CH: 1
4
SX1276
NET ID
PROG
POWER
HEART BEAT
V INPUT
Black - NEG
-
+
Red
+ POS
2332-010
Wire Polarity
Matters!
Power Power Transformer
Supply
18 GA. Wire 100 ft max
12VDC
16 GA. Wire 200 ft max
Do Not Connect Power To A Receptacle
Controlled By A Switch.
YELLOW
CHs match
and NET IDs
match
and both are
unique
Dual Band
Repeater Setup
See back page for an example.
1
4
7
Baseboard
NET ID: 2C CH: 3
4 4 4 4 4
BASE CH NET ID REMOTE CH
PROG
RESET
4
ON
ON
OFF
ADDRESS
RESET Button
Resets board after
adjustments have
been made.
Set ADDRESS to the
same as wireless
tracker board.
Press PROG buttons after setting
the CH and NET IDs on EACH side.
GREEN
CHs match
and NET IDs
match
and both are
unique
DBR
Tracker
A
2 3
5 6
Z
8 9
0
CALL Tracker
DBR Note: Typically up to 2
tracker expansion boards can
communicate with DBR. Up to
4 tracker expansion boards can
communicate with DBR in LOW
activity applications.
Range testing is HIGHLY recommended
before FINAL installation.
Up to 1500 ft
Remote Side
SX1276
Wireless
Tracker Board
REMOTE
BASE
SIG
SIG
Remote side communicates
BASE REMOTE
RF STRENGTH
with the wireless Tracker
board. The CH and NET ID of
the Remote side MUST match
RF SYNC
the CH and Net ID of the
DO NOT set Remote side the
RF LOST
same as the Base side.
2373-010 BASE
SIG
BASE SIG
Press to display
base side signal
strength.
RF STRENGTH LEDs (Base/Remote)
Off in normal operation. When signal is
displayed (press base/remote SIG button)
it is either green-good, yellow-weak or
red-NO. When signal is displayed, LED
blinks until signal is received, once
received, it stays lit.
Note: Signal display is terminated if either
Base or Remote PROGRAM button is
pressed or the number of minutes is
reached as selected by the SIG button.
RF SYNC LEDs (Base/Remote)
Off in normal operation. Blinks green
everytime data is received over the air.
RF LOST LEDs (Base/Remote)
Off in normal operation. Blinks when no air
data is detected after six minutes and stays
lit after NO air data is received for 10
minutes.
DoorKing Part Number
2332-080
900 MHz
Example:
The wireless
tracker board
MUST be set to:
NET ID: 2C CH: 3
Tracker board.
REMOTE
SIG
REMOTE SIG
Press to display
remote side signal
strength.