Advertisement
surrounding between 5%~95% without condensation.
Before power on, please confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running,
please avoid any direct contact in case of scalding.
【DIN-Rail Mounting】
For convenient usage in industrial environments, the product
adopts 35mm DIN-Rail mounting, mounting steps as below:
Step 1
Check if the DIN-Rail mounting kit is installed firmly.
Step 2
Insert the bottom of DIN-Rail mounting kit (one side
with spring support) into DIN-Rail, and then insert
the top into DIN-Rail.
Tips:
Insert a little to the bottom, lift upward and then insert
to the top.
Step 3
Check and confirm the product is firmly installed on
DIN-Rail, then mounting ends.
【Disassembling DIN-Rail】
Step 1
Device power off.
Step 2
After lift the device upward slightly, first shift out the
top of DIN-Rail mounting kit, then shift out the
bottom of DIN-Rail, disassembling ends.
【Power Supply Connection】
DC power supply
The device provides 6-pin 5.08mm pitch power supply input
terminal blocks and two independent DC power supply
systems, P1 and P2, which enables two
terminals to connect to the device. It
could ensure the normal operation of
the device when one of the systems
fails, thus improving the reliability of
network operation. Voltage range: 12~48VDC.
48VDC POE power supply input
Port 5 of this device supports PoE power receiving.
Note:
Power ON operation: first connect power line to the
connection terminal of device power supply, then power
on.
Power OFF operation: first unpin the power plug, then
remove the power line, please note the operation order
above.
【DIP Switch Setting】
This device provides 4-bit DIP switch for function setting,
where "ON" is enable valid terminal. The definitions of DIP
switch are as follows:
1. Restore factory setting
2.Reboot
3. Reserved
4. Reserved
【Console Port Connection】
This device provides 1 program debugging port based on
RS232 serial port which can conduct device CLI command
line management by connecting to PC. The interface adopts
RJ45 port. Its pin definitions are as follows:
No.
2
3
Pin Definition
TXD
RXD
【USB Port Connection】
Reserved
【SIM Slot】
This device provides 2 SIM slots. It would pops up after you
inserting a retrieve card pin in the little hole beside the SIM
slot, and then you should put the SIM card in the slot correctly
and insert the slot back in the router.
Note:
If the SIM card needs to be changed, the device should be
power off first in case of damaging the card.
【Serial Port Connection】
or 2 RS-485 serial ports. Its pin definitions are as follows:
PIN
1
RS-232
TXD
RS-485
Data-
(B)
【I/O Connection】
This device provides 10-pin 3.81mm pitch I/O input terminal
blocks (I/O port is the right 4-pin) ,
this function is temporarily reserved as the picture shows
above
【Checking LED Indicator】
The device provides LED indicators to monitor its operating
status, which has simplified the overall troubleshooting
process. The function of each LED is described in the table
below:
LED
Status
ON
5
WLAN
OFF
GND
This device provides 10-pin
3.81mm pitch serial port input
terminal blocks (the left 6-pin is
serial port) and supports 2 RS-232
2
3
4
5
6
RXD
GND
TXD
RXD
GND
Data+
GND
Data-
Data+
GND
(A)
(B)
(A)
Description
WIFI is running normally
WIFI is running abnormally or
closed
All indicators are out. It means
the LTE signal of the opposite
end is weak or no signal.
One indicator is on. It means the
LTE signal of the opposite end is
weak
Advertisement
