Related Manuals for Toolots NAX Series
Summary of Contents for Toolots NAX Series
- Page 1 NAX-Series Horizontal Saw Band Machine Tool with Pillar Operation Instruction Max. Cutting Diameter: Unit: mm Factory Serial No.:...
- Page 2 Catalog 1、 ……………………………………………1 ImportantNotes 2、 ……………………………………………3 Main Application 3、 ………………………………3 Normal Working Environment 4、 …………………………3 Main Models & Technique Parameters 5、 ………………………………3 Mechanical Transmission System 6、 …………………………………4 Key Structure of Machine Tool 7、 ………………………………………………6 Hydraulic System 8、 ………………………………………………9 Electrical System 9、...
- Page 3 3、 The operator shall be professional trained to ensure safe working and avoid harm or damage caused by false operation. 4、 The operation instruction shall be strictly followed to installate and operate the machine tool. There should be enough space for operate and the space shall be cleaned without obstacles to operator’s ensure safe operation and daily maintenance.
-
Page 4: Main Application
16、The power supply of the machine tool is 380V 50Hz AC Three Phase with the pressure inflate value less than 10%. Extra power supply, grounding and leakage protection devices should be set according to the rated capacity of the machine tool. Should there be possible of pressure inflate and false operation, shared wiring with other equipments is not permitted. - Page 5 Blade Size 1.3*41*5220 Motor Output Hydraulic Pressure 0.75 Coolant Pump 0.08 Table height Machine Size(L*W*H) 2560*1600*1700 Net Weight 2100 Vice clamping Hydraulic Blade tensioning form Maunal Feeding cut adjust way Hydraulic stepless Feeding way Manual Hydraulic cooling way Wind cooling Voltage 380V 50HZ 3Phase 5 、...
-
Page 6: Hydraulic System
Main Structure of the Machine Tool 6.1 Deceleration Worm Gear Box Part The part of the deceleration worm gear box lies beneath the frame. The linear speed of the saw band is changed by the transmission band wheel which is triggered by the main engine transmission band wheel. - Page 7 夹 紧 油缸 YA 4 1、Release the Emergency Stop button, the oil pump starts working. Adjust the overflow valve to push system pressure to required level. 2、Press the uplifting button. The upward mag valve and fast mag valve attract to each other so that the saw frame rises.
- Page 8 Take off and clean corresponding mag valve Keeping the oil clean could reduce accident and effectively prolong the service life of each mag valve. The hydraulic oil tank shall be cleaned regularly and the oil shall be replaced. 8 、 Electric and Control System 8.1 Power Supply The power supply for this machine tool is 380V 50Hz three-phase power.
- Page 9 SA/SB Button Φ22LAY-16 Emergency Stop Φ22LAY16 Button Working Light JC-15 AC36V Power LED XDJ2...
- Page 10 FU1（ 20A） FU2（2A） FU4（6A） KA1 KA1 KM 2 KA2 KA2 KM 1 KM 2 U V W KM 1 设 KM 2 备 KM 2 界 线 HL1 H L KM 1 KM 2 YA1 YA2 桥堆 工作灯 指示灯 油泵 钳紧...
- Page 11 with mag iron YA3, then the saw frame falls downward as in required speed. Press main engine stop button, relay KM2 opens and the main engine and water pump stop. 5、Press uplifting button, relay KA2 closes and the saw frame starts rising. Press fast fall button, relay KA2 opens while SB4 button closes and the saw frame falls down.
-
Page 12: Common Problems And Solutions
12 、 Machine Tool Debugging and Operation 12.1 Preparation Before Debugging Connect power supply and check if the motor is running in the right direction. Add in adequate cooling liquid in the cooling liquid tank. Put on the saw bank. Check if the emergency stop button works well and is reliable. - Page 13 The geometric Loose jaw Fasten the working part accuracy of the Saw band and the working Adjust working table cut part exceed requirement table are off plumb Saw band worn or broken Replace saw band Smoking while The cooling liquid could not Dredge the cooling cutting flow out fluently...
- Page 14 Short Saw Life High line speed Choose right speed Too much feed Decrease the feed Poor saw quality Replace saw band 1、 ions Problems Causes Solutions Turn on the 380V power not connected Connect power supply general switch Switch broken Replace but no power Emergency stop button not...
- Page 15 Saw frame not Lower limit travel switch not Adjust the switch rise after work connected touch-block part is cut Lower limit travel switch worn Replace and broken Rising mag valve blocked Take off and clean mag valve Saw frame Upper limit travel switch not switch touch-block rising could not connected...
- Page 16 Fuse burnt Replace...
Need help?
Do you have a question about the NAX Series and is the answer not in the manual?
Questions and answers