Table of Contents
Advertisement
Save these instructions. This manual will help you to obtain
efficient, dependable service from the heater, and enable
you to order repair parts correctly. Keep in a safe place for
Please read this entire manual before you install or use your
new room heater. Failure to follow instructions may result in
property damage, bodily injury, or even death. Improper
Installation Could Void Your Warranty!
If this heater is not properly installed, a house fire may result.
For your safety, follow the installation instructions. Never
use make-shift compromises during the installation of this
heater. Contact local building or fire officials about permits,
restrictions and installation requirements in your area.
Defender II
Owner's Manual Model: US1100E
future reference.
CAUTION!
U.S. Stove
227 Industrial Park Rd. South
Pittsburg, TN 37380, USA Phone:
(800)750-2723 www.usstove.com
Report Number: F19-473
Tested Per EPA Methods ALT-125, ASTM
E2515, ASTM E3053 and CSA B415
Certified to UL 1482-2011 (R2015) and
ULC-S627-00 (R2016)
Approved for mobile home installation
in USA and Canada
U.S. Environmental Protection Agency
Certified to comply with 2020
Ce produit peut vous exposer à des produits chimiques, y compris le
monoxyde de carbone, qui est connu dans l'État de Californie pour causer
particulate emissions standards.
le cancer, des malformations congénitales et / ou d'autres problèmes de
reproduction. Pour plus d'informations, visitez www.P65warnings.ca.gov
CALIFORNIA PROPOSITION 65 WARNING:
This product can expose you to chemicals including carbon monoxide, which
is known to the State of California to cause cancer, birth defects and/or other
reproductive harm. For more information, go to www.P65warnings.ca.gov
R
853363-0204i
Advertisement
Table of Contents
Related Manuals for U.S. Stove Defender II
Summary of Contents for U.S. Stove Defender II
- Page 1 Defender II Owner’s Manual Model: US1100E Save these instructions. This manual will help you to obtain efficient, dependable service from the heater, and enable you to order repair parts correctly. Keep in a safe place for future reference. CAUTION! Report Number: F19-473 Please read this entire manual before you install or use your new room heater.
- Page 2 This manual describes the installation and operation of the Defender II, US1100E wood heater. This heater meets the 2020 U.S. Environmental Protection Agency’s cordwood emission limits for wood heaters sold after May 15, 2020. Under specific test conditions this heater has been shown to deliver heat at rates ranging from 15,196 to 40,594 Btu/hr.
- Page 3 Assembly Step 1 - THE BLOWER ASSEMBLY MUST BE DISCONNECTED FROM THE SOURCE OF ELECTRICAL SUPPLY BEFORE ATTEMPTING THE INSTALLATION. With pliers, cut the 4 tabs and remove panel on the back of the stove. Note: Discard the panel. Step 2 - Fix the assembly to the back of the stove with the four screws provided. THE BLOWER ASSEMBLY IS INTENDED FOR USE ONLY WITH A STOVE THAT IS MARKED TO INDICATE SUCH USE.
- Page 4 Dimension Inch Stove Width 22.48 Stove Depth 20.76 *K Front Back M Left Right Total Width 38.48 Total Length 38.76 * Canadian installations require 18” (457mm) FLOOR PROTECTOR DIMENSIONS FREE STANDING STOVE CLEARANCES A wood stove must never be installed in a hallway or near a staircase, since it may block the way in case of fire or fail to respect required clearances.
- Page 5 SPECIAL MOBILE HOME REQUIREMENTS WARNING! - Do not install in a sleeping room CAUTION! - The structural integrity of the mobile home floor, wall, and ceiling/roof must be maintained. In addition to the previously detailed installation requirements, mobile home installations must meet the following requirements: •...
- Page 6 CHIMNEY CONNECTOR (STOVE PIPE) Your chimney connector and chimney must have the same diameter as the stove outlet (6”). If this is not the case, we recommend you contact your dealer in order to insure there will be no problem with the draft. The stove pipe must be made of aluminized or cold roll steel with a minimum thickness of 0.021”...
- Page 7 CHIMNEY Your wood stove may be hooked up with a 6” factory built or masonry chimney. If you are using a factory built chimney, it must comply with UL 103 or CSA-B365 standard; therefore it must be a Type HT (2100°F). It is extremely important that it be installed according to the manufacturer’s specifications.
- Page 8 MASONRY CHIMNEY Ensure that a masonry chimney meets the minimum standards of the National Fire Protection Association (NFPA) by having it inspected by a professional. Make sure there are no cracks, loose mortar or other signs of deterioration and blockage. Have the chimney cleaned before the stove is installed and operated. When connecting the stove through a combustible wall to a masonry chimney, special methods are needed.
- Page 9 FACTORY BUILT CHIMNEY When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed. You must also purchase (from the same manufacturer) and install the ceiling support package or wall pass-through and “T” section package, firestops (where needed), insulation shield, roof flashing, chimney cap, etc. Maintain proper clearance to the structure as recommended by the manufacturer.
- Page 10 COMBUSTIBLE WALL CHIMNEY CONNECTOR PASS-THROUGHS Method A. 12” (304.8 mm) Clearance to Combustible Wall Member: Using a minimum thickness 3.5” (89 mm) brick and a 5/8” (15.9 mm) minimum wall thickness clay liner, construct a wall pass-through. The clay liner must conform to ASTM C315 (Standard Specification for Clay Fire Linings) or its equivalent.
- Page 11 Wood Operating Instructions WOOD UTILIZATION Your heating unit was designed to burn wood only, no other materials should be burned. Waste and other flammable materials should not be burned in your stove. Any type of wood may be used in your stove, but specific varieties have better energy yields than others.
- Page 12 It is EXTREMELY IMPORTANT that you use DRY WOOD only in your wood stove. The wood should have dried for 9 to 15 months, such that the humidity content (in weight) is reduced below 20% of the weight of the log. It is very important to keep in mind that even if the wood has been cut for one, two or even more years, it is not necessarily dry, if it has been stored in poor conditions.
- Page 13 CAUTION: Never alter the damper slide or the adjustment range to increase firing for any reason. Doing so could result in heater damage and will void your warranty. HEATING Controlled combustion is the most efficient technique for wood heating because it enables you to select the type of combustion you want for each given situation.
- Page 14 We strongly recommend that you install a magnetic thermometer on your smoke exhaust pipe, approximately 18” above the stove. This thermometer will indicate the temperature of your gas exhaust fumes within the smoke exhaust system. The ideal temperature for these gases is somewhere between 275°F and 500°F. Below these temperatures, the build-up of creosote is promoted.
- Page 15 GLASS • Inspect and clean the glass regularly in order to detect any cracks. If you spot one, turn the stove off immediately. Do not abuse the glass door by striking or slamming shut. Do not use the stove if the glass is broken.
-
Page 16: Replacement Parts
Replacement Parts Key Part No. Description 29139 Air Deflector 891824 Heatshield Weldment 40292A 6” Flue Collar 88042 1/4” Rope Gasket 29055 Ashpan 610923 Pedestal Weldment (US1100E-BP) 610928 Damper Weldment 86709 Damper Rod 891987 Plastic Knob 610918 Access Panel (US1100E-BP) Ashpan Housing Weldment 610944 (US1100E-BL) 40566... - Page 17 Replacement Parts Part No. Description Qty. 893059 Wooden Thru Handle 893071 Door Handle 40887 Medium Arched Door 88324 1” Rope Gasket 893159 Clear Glass 29229 Glass Retainer, Sides 29227 Glass Retainer, Top 29230 Gasket Clamp 29228 Glass Retainer, Bottom 892294 Hinge Pin Part No.
- Page 18 Notes -18-...
- Page 19 Notes -19-...
-
Page 20: Service Record
Service Record It is recommended that your heating system is serviced regularly and that the appropriate Service Interval Record is completed. SERVICE PROVIDER Before completing the appropriate Service Record below, please ensure you have carried out the service as described in the manufacturer’s instructions. Always use the manufacturer's specified spare part when replacement is necessary. - Page 21 2. The part description / La description de la pièce____________________________________ 3. The model number / Le numéro de modèle_________________________________________ 4. The serial number / Le numéro de série_____________________________________________ U.S. Stove 227 Industrial Park Road South Pittsburg, TN 37380 USA Phone: (800)750-2723...