Information Leds; Operation; Storing A Position - Swedstyle Memory S Operating Manual

8 Swedstyle Memory S

5.2 Information LEDs

CONTAINER: This LED shows that the Containerstop function is active.
RESET: This LED shows that the control box is being reset.
FLEX: This LED shows that the Flex Function is active.
ERGOTRAINER: This LED shows that the Ergotrainer is active.
INFO: This LED warns you of important information on the position and information display.
PIN: This LED shows that the Pincode function is active.
6

OPERATION

CAUTION. Risk of minor or moderate injury through uncontrolled movement
The table may not always stop exactly at the expected position. Failure to anticipate the table's
movements may lead to minor or moderate injury through crushing. Wait until the system has
completely stopped before attempting to use the table
CAUTION. Risk of minor or moderate injury through unsecured objects
While the table moves up and down, unsecured objects may fall off the table and onto body
parts. This may lead to minor or moderate injury through crushing. Ensure loose objects are kept
away from the edge of the table. Do not leave unnecessary objects on the table during movement
CAUTION. Risk of minor or moderate injury through crushing
Failure to release Handset Keys correctly may result in the table failing to stop properly.
This may lead to minor or moderate injury through crushing. Do not slide your finger to a dif-
ferent Handset key while another button is pressed. Disconnect the system immediately if any
Handset Key becomes stuck.
INFO. The technology within the Handset may be interrupted by external interferences during
operation. This may lead to certain user inputs (i.e. button presses) not being recognized.
This section of the Operating Manual contains a selection of instructions for operating the Table
System to which the Handset is connected. Handset Keys are represented as follows:
UP Key
DOWN Key
UP Key - Motor group 2
DOWN Key - Motor group 2
1
Memory Position Key 1
2
Memory Position Key 2
3
Memory Position Key 3
4
Memory Position Key 4
S
Save key
Function Description
For an upward adjustment of he desk push this
button. Push this button until the desired height
of the desk has been reached.
For a downward adjustment of the desk push
this button. Push this button until the desired
height of the desk has been reached.
For an upward adjustment of the motor group
2 (e.g. monitor adjustment) or desk, push this
button. Push this button until the desired height
of the desk has been reached.
For a downward adjustment of the motor group
2 (e.g. monitor adjustment) or desk, push this
button. Push this button until the desired height
of the desk has been reached.
NOTE: In case of no motor group 2 attached the therefore assigned buttons
(motor group 2 upwards / motor group 2 downwards) are used for the desk upwards / desk
downwards functions.
4.4 Advanced Functions

6.1 Storing a position

Using this function you are able to store a desk-height.
4.4.1 Storing a position
4.4 Advanced Functions
Using this function you are able to store a desk-height.
4.4.1 Storing a position
Using this function you are able to store a desk-height. Note: On initial operation all stored positions are equal to the lowest
Using this function you are able to store a desk-height.
possible desk-height (lower end position).
Note: On initial operation all stored positions are equal to the lowest
possible desk-height (lower end position).
1. Move the table to the desired height.
Note: Only one desk-height per button is allowed.
1.
The display shows the Table Top height
Note: Only one desk-height per button is allowed.
1.
Move the desk to the position you want to store.
2.
The display reads the actual height of the desk (e.g. 73cm).
2. Press
S
1.
Move the desk to the position you want to store.
2.
Press the S button.
The display reads the actual height of the desk (e.g. 73cm).
3.
3. The display shows
The display reads S –.
2.
Press the S button.
3.
Press the position button of choice (e.g. S2).
3. Press the Memory Position Key The display reads S –. (e.g. 2)
2
4.
The display reads S 2.
3.
Press the position button of choice (e.g. S2).
4.
4. The display shows Now the height is stored on the chosen position button.
The display reads S 2.
The saving operation is confirmed with a double-click sound and after
4.
approximately 2 seconds the stored height will be displayed. Now the height is stored on the chosen position button.
5. Now the height is stored on the chosen position button.
The saving operation is confirmed with a double-click sound and after
approximately 2 seconds the stored height will be displayed.
The saving operation is confirmed with a double-click sound and
after approximately 2 seconds the stored height will be displayed.
NOTE: On initial operation all stored positions are equal to the lowest possible desk-height
(lower end position).
NOTE: Only one desk-height per button is allowed.
Page 9 / 12
Page 9 / 12
Swedstyle Memory S
Note
The desk will continue driving
upwards until you release the button, or the
maximum height is reached.
The desk will continue driving downwards until
you release the button, or the minimum height
is reached.
In case of no motor group 2 attached this button
is used for the Desk upwards function.
Motor group 2 will continue driving upwards
until you release the button, or the maximum
height is reached.
In case of no motor group 2 attached this button
is used for the Desk downwards function. Motor
group 2 will continue driving downwards until
you release the button, or the minimum height
is reached.
4.4 Advanced Functions
4.4.1 Storing a position
Note: On initial operation all stored positions are equal to the lowest
possible desk-height (lower end position).
Note: Only one desk-height per button is allowed.
Move the desk to the position you want to store.
(e.g. 73 cm)
The display reads the actual height of the desk (e.g. 73cm).
Press the S button.
The display reads S –.
Press the position button of choice (e.g. S2).
The display reads S 2.
Now the height is stored on the chosen position button.
The saving operation is confirmed with a double-click sound and after
approximately 2 seconds the stored height will be displayed.
Page 9 / 12
9