Advertisement
Quick Links
PTRIG™ SETUP MANUAL
PANORICS LLC. ALL RIGHTS RESERVED
ONLY FOR USE WITH PANORICS PRODUCTS
PTRig™ is patent pending. PTRig™ is a trademark of Panorics Corp. All rights reserved.
PTRig™ is compatible and works with GoPro® Hero4 cameras. GoPro, Hero, the GoPro logo, and the GoPro be a Hero Logo
are trademarks of GoPro, Inc. GoPro does not endorse, sponsor, approve of, or is in any way associated with PTRig™. If you
would like to buy GoPro products, please do so through GoPro or an authorized retailer, reseller or distributor.
By using this PTRig™ product with any of the above-mentioned third party products you take full and sole responsibility for any
early cancellation and termination of guarantee provided by such third parties or their service providers. PTRig™ takes no direct
or indirect obligation or liability for any direct or consequential losses, damages to property or moral damages, your self-made
installation of this PTRig™ product or any damage you can make to it or to any third party product.
The PTRig™ installation manual is for information purposes only and was not approved or recommended, or included in the
technical guarantee provided by any third party including but not limited to GoPro, Inc. By purchasing this product you accept
full responsibility. PTRig™ does not come with any warranty. Panorics Corp. does not have a return policy and all PTRig™
products are purchased "as is".
Advertisement
Summary of Contents for Panorics PTRIG
- Page 1 PTRig™ is compatible and works with GoPro® Hero4 cameras. GoPro, Hero, the GoPro logo, and the GoPro be a Hero Logo are trademarks of GoPro, Inc. GoPro does not endorse, sponsor, approve of, or is in any way associated with PTRig™. If you would like to buy GoPro products, please do so through GoPro or an authorized retailer, reseller or distributor.
- Page 2 INCLUDED IN THE PACKAGE The package has all the necessary parts for assembling PTRig camera and includes the following: PTRig body and cover • A set of three lenses for GoPro cameras • GoPro bracket • Set of mounting screws: the small ones for the cover and the large ones for the adapter •...
- Page 3 GOPRO CAMERA SETUP Prior to installing the GoPro cameras in the PTRig, replace the original GoPro lenses with the provided fisheye lenses. 1. Remove the lens rings Lift up the ring by using a thin and flat screwdriver. GoPro H4 ring is made of plastic and latches are used to keep it firmly in several places.
- Page 4 You will hear a slight click-sound when the glue lets the lens out and then the lens will easily come off. Remove the lenses from all three cameras. PTRIG S ETUP M ANUAL 4 ...
- Page 5 3. Place GoPro cameras in the PTRig body Place all three cameras in the PTRig body with GoPro backs facing the center of the body. The camera screens shall be directed toward the top of the body. PTRIG S ETUP M ANUAL ...
- Page 6 4. Set the cover on the PTRig body When all the cameras are placed into the PTRig body, put the cover on top of the body and slide it down to fully cover the cameras. PTRIG S ETUP M ANUAL ...
- Page 7 The installation of the rings does not affect the quality of video shooting or any mechanical properties of PTRig, so installing them is optional and can be omitted. PTRIG S ETUP M ANUAL ...
- Page 8 6. Tighten the small screws on PTRig cover Attach the PTRig cover to the body. To do so, use small screws for holes right below the lenses. Attention: excessive pressure in tightening the screws may damage the cover or the body, so tighten the screws carefully.
- Page 9 Before attaching the lenses to the cameras, carefully check that the mounting holes and image sensors are clean and there is no dust on them. If there is dust, clean the space. Place the PTRig lens into the lens-mounting hole and turn five-seven times clockwise. Attach all the other PTRig lenses in the same way.
- Page 10 1080p at 60fps operation mode and connect the camera to the monitor with the HDMI cable (insert the cable in the microHDMI port on the camera at the bottom of PTRig). The image from the camera may appear blurred. Adjust the lens by rotating it clockwise until the image on the monitor becomes clear and sharp.
- Page 11 PTRig comes with a special adapter which allows to attach PTRig to monopods and tripods with standard GoPro accessories. Flip PTRig and attach the adapter to the bottom of the body with the flat side. Attach the bracket to the body bottom and tighten with the big screws (included in the package).
- Page 12 Shoot 360-degree video with PTRig To shoot 360-degree video using PTRig, all three GoPro cameras must be set up at the same operational mode. The following settings can be applied: 1440p: the resulting spherical video will have up to 2800x1400px resolution •...
- Page 13 We wish you great 360-degree videos and THANK YOU for using our products! If you would like to feature your spherical video shot with PTRig on our websites or social networks or just want to share the joy with us, do not hesitate to send us a link at info@panorics.com.