Table of Contents Safety Installation guidelines Grounding/Lightning protection Installation site selection guidelines Installation Mechanical guidelines Installation A. Fixing the Easy-fix LNB Arm to Back Mount B. Reflector fixation C. LNB Holder fixation D. Fastening the U-Mount Clamp to the mast E.
Safety The Inverto parabolic antennas are intended solely for the reception of satellite signals and for use only as a do- mestic antenna. The antenna should have no more than 6m free mast length and a fixed-end moment up to 1650 Nm.
GROUNDING/LIGHTNING PROTECTION Because of the serious consequences if the work is not done properly, grounding and lightning protection work may be performed only by specially trained electricians! Never perform grounding and lightning protection work if you are not a specialist with the appropriate skills! •...
INSTALLATION SITE SELECTION GUIDELINES It is essential to select the correct installation site. This determines whether your parabolic antenna can be erected safely and perform optimally. When selecting the installation site, take account of special features of the structure of the building. If the installation is at the edge of the roof or the building or on a cylindrical structure, DIN 1055, parts 4 and 4131 specify the increased wind and vibration loadings that should be allowed for.
Installation A. FIXING THE EASY-FIX ARM TO BACK MOUNT Insert the Easy-fix LNB Arm (1) into the Back Mount (2) as shown in the drawing below. Make sure the rectangular opening at the end of the Easy-fix LNB Arm is located at the opposite end to the Back Mount and the Plastic Profile Stopper (3) is inserted into the Easy-Fix LNB Arm and is facing the Back-Mount.
B. REFLECTOR FIXATION Pass the Easy-fix LNB Arm through the Reflector (6) and use the supplied four pairs of M8x15 Screws (7) and M8 Nuts (8) to secure them together (90/120cm model includes six pairs). Description Quantity Coated Reflector M8x15 Square Foot Screw (6 for 90/120cm reflector) M8 Flange Nut (6 for 90/120cm reflector)
C. LNB HOLDER FIXATION Place the LNB (not supplied) inside the LNB Holder (9) as shown in the drawing below. Close the two parts of the LNB Holder as shown in the drawing below. Secure the 2 parts of the LNB Holder using the supplied Screw (10).
Slide the LNB Holder into the profile of the Easy-Fix LNB Arm until it clicks. Description Quantity LNB Holder LNB Holder screw with nut D. FASTENING THE U-MOUNT CLAMP TO THE MAST Hold the U-Mount Clamp(11) and pass the U-Bolts (12) until they are positioned as shown in the drawing below. Place the two Mast-Clamps (13) at the ends of the U-Bolts and screw on the for supplied M8 Nuts (14).
E. FIXING THE U-MOUNT CLAMP TO THE BACK-MOUNT Attach the U-Mount Clamp to the Back Mount as shown in the drawing below and use the supplied two M8x70 Heavy Hex Flange Screws (15) and M8 Flange Nuts (16) to fasten them together. You may use the elevation marks in order to set the desired elevation degree.
The MultiConnect system has been granted patent rights in Germany and is in the process of being granted Patent for the rest of the EU. Inverto also offers an extensive range of LNBs for any type and scenario of installation. For more information on the MultiConnect system or other LNB models, please, visit our web...
Page 18
60,80,90,120cm Offset-Antenne mit Easy-fix Arm Installationshandbuch für die Modelle: IDLB-STCF60-KULGO-LPS IDLB-STCF80-KULGO-LPS IDLB-STCF90-KULGO-LPS IDLB-STC120-KULGO-LPS IDLB-ALCF60-KUANO-LPS IDLB-ALCF80-KUANO-LPS IDLB-ALCF90-KUANO-LPS...
Page 19
Inhaltsübersicht Sicherheit Installationshinweise :Grundlegende Sicherheitsvorkehrungen Erdung der Satellitenschüssel /Blitzschutz Hinweise zum Montagestandort Montagehinweise Installation A. Befestigung des EasyFix-Arms am Rückenteil B. Befestigung des Reflektors C. Befestigung der LNB-Halterung D. Befestigung der U-förmigen Mastklemme am Mast E. Befestigung der U-förmigen Mastklemme am Rückenteil Technische Daten Zubehör Azimut-/Elevationstabelle...
Sicherheit Satellitenanlagen von Inverto dienen ausschließlich dem Empfang von Satellitensignalen und dürfen nur als Haus- haltsantennen verwendet werden. Die Satellitenschüssel sollte maximal 6 Meter freier Mastlänge und ein Einspan- nmoment bis zu 1650 Nm aufweisen. Die Anlage ist nicht für die Montage an Gebäude, die anfällig für Erschütter- ungen sind, entwickelt.
• Es besteht Lebens- und Verletzungsgefahr durch einen möglichen Sturz vom Dach, Durchbruch durch das Dach und durch herabstürzende Teile. Zudem besteht das Risiko, dass das Dach Schaden nimmt. • Halten Sie die lokalen Sicherheitsvorschriften ein. • Jegliche andersartige Verwendung oder Nichtbeachtung der Anweisungen führt zu Haftungsausschluss. overage.
HINWEISE ZUM MONTAGESTANDORT: Die Wahl des richtigen Montagestandorts entscheidet darüber, ob ihre Satellitenschüssel stabil aufgestellt werden und die optimale Leistung erzielen kann. Bei der Wahl des Montagestandorts sind die Besonderheiten des jeweiligen Gebäudes zu beachten. Falls Sie die Montage an Dach- oder oder Gebäudekanten oder an zylindrischen Bauwerken durchführen, ist nach DIN 1055, Teil 4 und 4131 mit erhöhter Wind- und Erschütterungsintensität zu rechnen.
Installation A. BEFESTIGUNG DES EASYFIX-ARMS AM RÜCKENTEIL Stecken Sie den EasyFix LNB Arm (1) in das Rückenteil (2) der Satellitenschüssel wie in der Zeichnung unten abgebildet. Vergewissern Sie sich, dass sich die viereckige Öffnung am Ende des EasyFix LNB Arm an der gegenüberliegenden Seite des Rückenteils befindet.
B. BEFESTIGUNG DES REFLEKTORS Stecken Sie den EasyFix LNB Arm von der Rückseite durch den Reflektor (6). Verwenden Sie die vier mitgelieferten M8x15-Schrauben (7) und M8-Flenschmuttern (8), um diese beiden Elemente aneinander zu befestigen (beim 90/120cm-Modell sind es jeweils sechs Schrauben bzw. Muttern). Beschreibung Menge Beschichteter Reflektor...
C. BEFESTIGUNG DER LNB-HALTERUNG Befestigen Sie den LNB (nicht im Lieferumfang enthalten) an der LNB-Halterung (9/10) wie in der Zeichnung unten abgebildet. Schließen Sie die zwei Elemente der LNB-Halterung wie auf der unteren Zeichnung zu sehen. Befestigen Sie die zwei Elemente der LNB-Halterung mit der mitgelieferten Schraube.
Page 26
Schieben Sie die LNB-Halterung in den EasyFix LNB Arm bis sie hörbar einrastet. Beschreibung Menge LNB-Halterung Schraube und Mutter für die LNB-Halterung D. BEFESTIGUNG DER U-FÖRMIGEN MASTHALTERUNG AM MAST Nehmen Sie die U-förmige Masthalterung (11) und führen Sie die Schrauben (12) hinein bis diese sich an der Position befinden, die in der Zeichnung unten dargestellt wird.
E. BEFESTIGUNG DER U-FÖRMIGEN MASTKLEMME AM RÜCKENTEIL Bringen Sie nun die U-förmige Masthalterung am Rückenteil an wie in der Zeichnung unten dargestellt und verwenden Sie zur Befestigung die mitgelieferten M8x70-Schrauben (15) und M8-Muttern (16). Sie können die Neigungsskala verwenden um den gewünschten Neigungswinkel (Elevation) einzustellen. Beschreibun Menge M8x70 Sechskantschrauben...
Das MultiConnect-System ist in Deutschland patentiert. Ein Patent für die restliche EU ist in Bearbeitung. Inverto bietet eine sehr große Auswahl an LNBs für verschiedene Anwendungen und Installationsarten. Weitere Informationen zum MultiConnect-System oder zu anderen LNB-Modellen finden Sie auf unserer...
Need help?
Do you have a question about the IDLB-STCF60-KULGO-LPS and is the answer not in the manual?
Questions and answers