Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TREND Snappy T50
Summary of Contents for TREND Snappy T50
-
Page 3: Table Of Contents
Dear Customer TECHNICAL DATA Thank you for purchasing this Trend product, we hope you enjoy many years of creative and Voltage: UK & Eire productive use. No load speed: (min.) 0-2,300 rpm Please remember to return your guarantee card Impact rate: 0-3,000 ipm within 28 days of purchase. -
Page 4: Safety
SAFETY 13. Do not use tool if switch does not 4. Dress properly. Do not wear loose turn it on or off. Have defective clothing or jewellry, they can be WARNING: switches replaced by an Authorised caught in moving parts. Rubber Service Agent gloves and non-skid footwear is Observe the safety regulations in the... -
Page 5: Electrical Safety - Power Supply
0.75 below. If you are in doubt, contact an authorised 1.00 Trend repair agent or a qualified electrician. 1.50 ■ Disconnect the plug from the supply. 2.50 ■ Cut off the plug and dispose of it safely; a 4.00... -
Page 6: Safety Instructions For Battery Charger
15 minutes. After this time you can charge a second battery pack. ■ Do not disassemble charger; take it to a Trend Service Agent when service or repair is required. 230 volts present at charging terminal. - Page 7 Unplug charger before ■ Charge the battery packs only in a Trend attempting to clean. charger. ■ Do not freeze or immerse charger in water or ■...
-
Page 8: Additional Safety Rules For Impact Driver
Important Information for Recharging Hot Batteries When using your cordless impact driver continuously, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, the red light on the charger will flash. -
Page 9: Manufacturers Declaration
INFORMATION ON NOISE/VIBRATION The noise level when working can exceed 85 dB(A). Wear ear protection! Weighted root mean square acceleration value according to EN 60745: < 30.61 m/s (hand arm method) Managing Director Jeff Willcocks Trend Machinery & Cutting Tools Ltd. -
Page 10: Description Of Parts
DESCRIPTION OF PARTS A Variable speed switch B Forward / reverse button C Quick release chuck D Pistol grip E LED lights F Brush cap G Battery H Battery release button Charger LED charger indicator K Metal front housing assembly L Pozi ®... -
Page 11: Assembly & Adjustment
■ Tightening a screw with the impact ASSEMBLY & ADJUSTMENT driver at an angle to the screw can damage the head of the screw and Installing/Removing Driver Bit proper force will not be transmitted Always follow the following procedure to install driver bit:- to the screw. - Page 12 ■ After normal use, the battery pack will require one hour of charging before it will be fully Depending on room temperature, line charged. A completely discharged battery will voltage, and existing charge level, require one and a half hours in order to be initial battery charging may take fully charged.
-
Page 13: Operation
4. Bolt Size: Larger bolt diameters generally OPERATION require higher fastening torque. Fastening torque will also vary according to length, grade, and torque coefficient. Switch Operation 5. Material: The type of material and surface ■ This switch has a built-in, electronic circuit finish of the material will affect fastening that can vary the rotation speed. -
Page 14: Accessories
It is advisable to have the brushes Instead, take the batteries to a Trend Service Agent, your local Trend Stockist or a local recycling replaced by an authorized Trend station. If necessary contact your local municipality Service Agent. -
Page 15: Spare Parts - Spare Parts List
T50 - SPARE PARTS LIST v1.0 10/2006 Desc. Ref. Housing Assembly (Left & Right) WP-T50/001 LED Cover WP-T50/002 Switch 12V WP-T50/003 Motor 12V WP-T50/004 Hammer and Gearbox Assembly WP-T50/005 Front Cover Assembly WP-T50/006 Carbon Brush 12V (1 pair) WP-T50/007 Brush Cap WP-T50/008 Wrist Strap WP-T50/009... -
Page 16: Spare Parts Diagram
T50 - SPARE PARTS DIAGRAM v1.0 10/2006 T 5 0 -14-... - Page 17 NOTES -15-...
- Page 18 NOTES -16-...
- Page 20 Web: __________________www.trend-uk.com RECYCLABLE © Copyright Trend 2006. No part of this publication may be reproduced, stored or transmitted in any form without prior permission. Our policy of continuous improvement means that specifications may change without notice. Trend Machinery and Cutting Tools...
Need help?
Do you have a question about the Snappy T50 and is the answer not in the manual?
Questions and answers