Related Manuals for Aardenburg BETA M Series
Summary of Contents for Aardenburg BETA M Series
- Page 1 BETA M (door) Flail Mulcher Operation, Service Aardenburg Machinery BV. ALPHA BETA M (door)
-
Page 2: Table Of Contents
8.2 Safe operation and maintenance of the machine 8.2.1 Connection between tractor and operating machine 8.2.2 Protection of moving drive parts 8.2.3 Projection of materials 8.2.4 Noise 8.2.5 Personal protection devices 8.2.6 Stability Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 3: Guarantee
These general guarantee terms replace and cancel all previous explicit or implicit guarantee conditions. Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 4: Guarantee Certificate
Date of compilation: Date of delivery: Purchaser’s signature: GUARANTEE CERTIFICATE (copy for the manufacturer) Purchaser’s data Type of machine Last name: Model: Name: Code: Address: Serial number: Date of compilation: Date of delivery: Purchaser’s signature: Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 5: Introduction
Always remember that the high inertia of the rotor means that it needs a few minutes before it stops. WARNING: In certain work situations the machine may project shredded material: always respect safety distances and make sure they are respected! Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 6: Machine Model And Basic Components
3.1 MACHINE BASIC COMPONENTS Pos. Name Side guard Frame Side shift cylinder Articulation cylinder Gearbox Universal joint housing Transmission cover Upper link pin Drawbar Foot Parallel hitch pins Parallelogram Flaps Rotor Levelling roller Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 7: Functional Characteristics
The high strength 10.9 (UNI 3740) fastening screw guarantees a sure connection and duration that corresponds to the duration of the tools. WARNING: INSTALL ONLY ORIGINAL TOOLS ON THE ROTOR!! TYPES OF TOOLS Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 8: Cardan Shaft
(that cannot be caught by the machine or pulled into it), especially close-fitting garments (such as work overalls with safety wrists and ankles); Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 9: Installing The Machine
Remove the three-point drawbar from the packing and set it on the ground; Move the parallelogram arms with care and attention until they are centered on their connection holes; Move the jack and fasten it in place with its pin. Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 10: Connection To The Three-Point Hitch
10. slightly lift the machine off the ground and lift the parking stand (6); 11. connect the cylinder drive hoses; Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 11: Installing The Cardan Shaft
When the machine is put away for storage always set the cardan shaft on its specific support bracket S provided on the three-point drawbar to avoid build-up of dirt or deformation or breakage of the protective guard. Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 12: Disconnecting The Machine
C to the hook S Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 13: Operating Instructions
Disengage the P.T.O. before lifting the machine, do not operate the machine while it is lifted and always stop the machine before descending from the tractor; Respect safe distances when working near houses or roads: 5.1. 5 meters on the side; 5.2. 10 meters to the rear. Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 14: Use In The Field
EXCESS SPEEDS put excessive stresses on drive components, wearing them out ahead of time. This will produce poor-quality shredded material, the possible expulsion of large pieces of material which, because of their higher inertia may be projected beyond forecast safety limits. The following Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 15: Machine Maintenance
Comply with currently valid legislation in your own country regarding environmental protection and waste disposal legislation. It is good practice, when changing oil, to wear protective gloves. Carefully wash body parts of the skin comes in contact with the used oil. Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 16: Preventive Guidelines
Personal Protection Measures. WARNING: THE P.T.O. MUST BE DISENGAGED AND THE TRACTOR OFF AND PROPERLY BRAKED OR DISCONNECTED BEFORE BEGINNING ANY MAINTENANCE PROCEDURES Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 17: Greasing And Lubrication
The rotor is lubricated from the pulley side using the grease nipple placed on the tube that exits from the transmission casing. S – joint grease every 20 work hours. P – parallelogram grease every 20 work hours. Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 18: Belt Tensions
3. tighten the belts by operating on the tightening screws T; 4. clamp the screws T; 5. tighten screws V; 6. reinstall the cover and fasten them with screws. WARNING: DO NOT WORK WITHOUT THE BELT COVER Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 19: Replacing Tools
9. turn the machine back into its normal operating position. OUR ORIGINAL SPARE PARTS GUARANTEE COMPLETE AND CORRECT MACHINE OPERATION. Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 20: Operating Test
Check the tools if the machine vibrates during the test (see paragraphs 7.5.1 and 7.5.2). The rotor will need to be dynamically balanced if the machine vibrates after the tools are checked or replaced. In this case turn to your local retailer. Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 21: General Precautions
These regard, in particular: connection between tractor and operating machine; protection of moving drive parts; projection of materials; noise; personal protection devices (DPI); stability. Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 22: Connection Between Tractor And Operating Machine
Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 23: Projection Of Materials
MANDATORY MANDATORY MANDATORY MANDATORY MANDATORY MANDATORY FACE HEARING BODY PROTECTION SAFETY SHOES SAFETY GLOVES PROTECTION PROTECTION PROTECTION Aardenburg Machinery BV. ALPHA BETA M (door) -
Page 24: Stability
= tractor wheel axle / axle distance (m) At least 20% of the total tractor operating machine mass must bear on the front axle of the tractor when it is in working order. Aardenburg Machinery BV. ALPHA BETA M (door)
Need help?
Do you have a question about the BETA M Series and is the answer not in the manual?
Questions and answers