Advertisement
Quick Links
WARNING! Strictly follow all instructions to avoid an accident, damage to property,
personal injury or death. See www.harken.com/manuals for additional safety information.
WARNING! This product is not to be used for human suspension. Components may fail
causing person to fall, possibly resulting in serious injury or death.
SAVE TIME! READ THE ENTIRE MANUAL BEFORE BEGINNING HOISTER INSTALLATION.
KIT INCLUDES
A 1 welded screw eye
B 4 pigtail lag screws
C 1 shackle
D 4 pulleys
E 2 webbing straps with buckles
7' (2.13 m)
F 1 single black/red hoisting rope
G 1 block and tackle with
cleat (G1) and rope
H 4 black drop ropes: 2 long, 2 short
I 4 lag bolts
/
" x 2
/
1
1
4
J 4 washers
/
" (6 mm)
1
4
K 2 organizer plates
L 2 organizer pulleys
PURCHASE SEPARATELY IF NEEDED –
See "note" Step 1B, page 6.
1 pine board (riser) (grade 2)
2" x 6" x 7" (50 mm x 152 mm
x 180 mm) not used for rafters
running sideways
2 pine boards (grade 2) 2" x 6" x 6'
(50 mm x 152 mm x 1.83 m)
8 lag bolts and washers
(8 x 100 mm)
PURCHASE ADDITIONAL FOR RAFTERS
RUNNING SIDEWAYS – See Step 2A, page 7
1 pine board (grade 2) 2" x 4" x 6'
(50 mm x 100 mm x 1.83 m)
2 lag bolts and washers
(8 mm x 90 mm)
TOOLS
Drill
Plumb line
Drill bits:
/
" (4 mm)
Pencil
5
32
/
" (6 mm)
Stud finder
7
32
Stepladder
/
" (8 mm
5
16
Harken, Inc. • N15W24983 Bluemound Rd, Pewaukee, WI 53072-4974 • Tel: 262-691-3320 • Fax: 262-701-5780 • Email: hoister@hoister.com • Web: www.hoister.com
Welded screw eye
A
E
Webbing straps with buckles
" (6 x 63 mm)
2
/
" x 4"
5
16
/
" x 3
/
"
5
1
16
2
Safety glasses
Tape measure
Wrench (box end or
ratcheting)
Pigtail lag screws
B
HCP1443
HCP1444
(G1) Cleat
7758ASSY
HCP1459.SET
DO NOT UNTIE
Single black/red hoisting rope
F
HCP1483
/
" (11 mm)
7
16
Shackle
C
072
224A
Block and tackle*
G
Rope organizer components
Lag bolts
I
HFS908
J
Washers
HFS913
IMPORTANT SAFETY INFORMATION
• NEVER USE TO LIFT A PERSON.
• DISABLE AUTOMATIC GARAGE DOOR OPENER
when installing, raising, or lowering Hoister.
• READ ENTIRE MANUAL CAREFULLY BEFORE
starting installation. It will save you time.
• DO NOT UNTIE ANY ROPES
System comes ready to install.
Leave F, G, and H together.
• DO NOT RAISE OR LOWER HOISTER
with anyone standing under object.
Pulleys
D
224A
DO NOT UNTIE
Drop black ropes
H
HCP1447/HCP1448
Organizer plates
K
H-28375A
Organizer pulleys
L
H-52010
Advertisement
Related Manuals for Harken Hoister SUP
Summary of Contents for Harken Hoister SUP
- Page 1 WARNING! Strictly follow all instructions to avoid an accident, damage to property, personal injury or death. See www.harken.com/manuals for additional safety information. WARNING! This product is not to be used for human suspension. Components may fail causing person to fall, possibly resulting in serious injury or death. SAVE TIME! READ THE ENTIRE MANUAL BEFORE BEGINNING HOISTER INSTALLATION.
- Page 2 BEFORE STARTING INSTALLATION Determine the rafter direction and follow the instructions for rafters running: FRONT-TO-BACK or SIDEWAYS RAFTERS RUNNING FRONT-TO-BACK Front wall Garage door RAFTERS RUNNING SIDEWAYS Garage door Front wall...
-
Page 3: Installation Overview
INSTALLATION OVERVIEW PART 1: ASSEMBLY FOR RAFTERS RUNNING FRONT-TO-BACK Pigtail Pigtail lag screw lag screw INSTALLATION OVERVIEW Page 4 STEP 1: Determine Hoister location Page 5 - 6 2" x 6" x 7" riser board (50 mm x 152 mm x 180 mm) Organizer STEP 2: Install mounting boards Page 7... - Page 4 PART 1: ASSEMBLY FOR RAFTERS RUNNING FRONT-TO-BACK INSTALLATION OVERVIEW STEP 1: Determine Hoister location Page 5 - 6 Pigtail Pigtail lag screw lag screw STEP 2: Install mounting boards Page 7 STEP 3: Install pigtail lag screws Page 8 2" x 6" x 7" riser board (50 mm x 152 mm x 180 mm) STEP 4: Install rope organizer...
- Page 5 OPTION 1. Above garage door: Make sure there is enough Measure length of SUP. Position Hoister so garage door clearance to lift and store SUP above open garage door. can open with SUP lowered. Opened...
- Page 6 Greater distance is okay and distance for long, lightweight objects can be less as stated above. rafters. Position Hoister directly above SUP to be lifted. If installing without mounting boards, go to Opened...
- Page 7 STEP 2: INSTALL MOUNTING BOARDS; RAFTERS RUNNING FRONT-TO-BACK A. DRILL CEILING RAFTER ATTACHMENT POINTS B. DRILL MOUNTING BOARD Measure center-to-center distance between " LOCATE CEILING RAFTERS (5.5 mm) rafter holes. Mark distance on mounting Mounting boards must attach to ceiling rafters boards.
- Page 8 (50 mm) outside board " Drill (5.5 mm) hole at each outside point Pull vehicle into garage with SUP on car rack. Disconnect automatic garage door. MARK LOCATION POINTS 2" (50 mm) Drill hole Use plumb line to locate four lifting points on mounting point boards above vehicle.
- Page 9 MAXIMIZING LOWERING OF SUP welded screw eye. Always wear safety glasses. Screw welded You may want to lower SUP to floor or onto sawhorses. screw eye into top plate until threads just disappear into top If distance 2 is much greater than 3, the distance SUP plate.
- Page 10 PART 2: ASSEMBLY FOR RAFTERS RUNNING SIDEWAYS INSTALLATION OVERVIEW Alternate position for rafters that run sideways. STEP 1: Determine Hoister location Page 11 - 12 2" x 6" Mounting boards 50 mm x 152 mm STEP 2: Install mounting boards Page 13 2"...
- Page 11 Opened garage door OPTION 2. Below garage door: Use if not enough clearance for above garage door storage (Option 1). SUP has clearance to lift and store below open garage door. Opened garage door DIAGRAM 13. Plan to position SUP above car with clearance to open garage door.
- Page 12 Opened garage door Opened garage door DIAGRAM 14. Center SUP under mounting points. Position mounting boards so lifted object is balanced. Plan location of mounting boards and welded screw eye. 2" x 4" STEP 1B 1) Length of mounting boards.
- Page 13 Use plumb line to locate four lifting points on mounting PULL VEHICLE INTO GARAGE boards above vehicle. 2" 2" (50 mm) (50 mm) SUP width Ceiling Front view Pull vehicle into garage with object on car rack. Disconnect automatic garage door.
- Page 14 STEP 3 CONTINUED: INSTALL PIGTAIL LAG SCREWS; RAFTERS RUNNING SIDEWAYS INSTALL PIGTAIL LAG SCREWS VIEWED FROM BELOW Mounting board Mounting board Mounting board Mounting board Mounting board Mounting board Mounting board 2" x 6" Mounting boards 50 mm x 152 mm Overtightened 2"...
- Page 15 Pigtail lag screw DIAGRAM 21. If distance to front wall is less than distance needed to lift SUP, move the welded screw eye (A) along the front wall until distance 2 is equal to distance 3 (see Diagram 20). Drill a "...
- Page 16 PART 3: FOR ALL ASSEMBLIES STEP 6: ASSEMBLE HOISTER SYSTEM FOR ALL ASSEMBLIES B. ATTACH PULLEYS Place one pulley (D) on each pigtail lag screw (B). Ceiling Front wall ATTACH BLOCK AND TACKLE (G) DIAGRAM 22. Avoid installing welded screw eye above tall shelves. Attach block and tackle system (G) to welded screw Rope must point down to lock.
- Page 17 DIAGRAM 25. Put all four black drop ropes through organizer. DIAGRAM 26. Tie knots below top of SUP so it can be lifted to ceiling. Adjust strap length in buckle as needed. Put two shorter black drop ropes through pulleys (D) on mounting board with rope organizer.
- Page 18 Securely grip rope, apply tension, and angle it away from front wall. Bring arm up to let rope out and then back toward the wall to lock the rope. Repeat until SUP With rope pointed down, the cleat will lock the rope.
-
Page 19: Warranty
APPENDIX WARRANTY WARRANTY BLOCK AND TACKLE RUNNING TO SIDE WALL What is covered – This warranty covers defects in Rafters running front-to-back materials or workmanship. Lead block and tackle at 90 degrees to a conventional direction. Who is covered – The original purchaser. Organizer mounted to 2"... - Page 20 5050 7/17 Printed in USA...