Table of Contents
Advertisement
Quick Links
Harken, Inc. • N15W24983 Bluemound Rd, Pewaukee, WI 53072-4974 • Tel: 262-691-3320 • Fax: 262-701-5780 • Email: hoister@hoister.com • Web: www.hoister.com
WARNING! Strictly follow all instructions to avoid an accident, damage to property,
personal injury or death. See www.harken.com/manuals for additional safety information.
WARNING! This product is not to be used for human suspension. Components may fail
causing person to fall, possibly resulting in serious injury or death.
SAVE TIME! READ THE ENTIRE MANUAL BEFORE BEGINNING HOISTER INSTALLATION.
KIT INCLUDES
A 1 Welded screw eye
B 4 Pigtail lag screws
C 1 Shackle
D 4 Pulleys
E 2 Webbing straps with buckles
7' (2.13 m)
F 1 Single black/red hoisting rope
G 1 Block and tackle with
cleat (G1) and rope
H 4 Black drop ropes: 2 long, 2 short
I 4 Lag bolts
/
" x 2
/
1
1
4
J 4 Washers
/
" (6 mm
1
4
K 2 Organizer plates
L 2 Organizer pulleys
PURCHASE SEPARATELY IF NEEDED –
See "Note" Step 1b
1 Pine board (riser) (grade 2)
2" x 6" x 7" (50 mm x 152 mm
x 180 mm) Not used for rafters
running sideways
2 Pine boards (grade 2) 2" x 6" x 6'
(50 mm x 152 mm x 1.83 m)
8 Lag bolts and washers
(8 x 100 mm)
PURCHASE ADDITIONAL FOR RAFTERS
RUNNING SIDEWAYS – See Step 2A
1 Pine board (grade 2) 2" x 4" x 6'
(50 mm x 100 mm x 1.83 m)
2 Lag bolts and washers
(8 mm x 90 mm)
TOOLS
Drill
Drill bits:
/
" (4 mm)
5
32
/
" (6 mm)
7
32
/
" (8 mm
5
16
Welded screw eye
A
HCP1443
E
Webbing straps with buckles
HCP1459.SET
" (6 x 63 mm)
2
F
Single black/red hoisting rope
/
" x 4"
5
16
/
" x 3
/
"
5
1
16
2
Plumb line
Safety glasses
Pencil
Tape measure
Stud finder
Wrench (box end or
ratcheting)
Stepladder
Pigtail lag screws
B
HCP1444
(G1) Cleat
7758ASSY
Block and tackle*
G
DO NOT UNTIE
HCP1483
IMPORTANT SAFETY INFORMATION
• DISABLE AUTOMATIC GARAGE DOOR OPENER
when installing, raising, or lowering Hoister.
• READ ENTIRE MANUAL CAREFULLY BEFORE
starting installation. It will save you time.
• DO NOT RAISE OR LOWER HOISTER
/
" (11 mm)
7
16
SUP
SUP
7808: 45 lb (20 kg) System
Shackle
C
072
DO NOT UNTIE
224A
H
HCP1447/HCP1448
Rope Organizer Components
Lag bolts
I
K
HFS908
J
Washers
L
HFS913
• NEVER USE TO LIFT A PERSON.
• DO NOT UNTIE ANY ROPES
System comes ready to install.
Leave F, G and H together.
with anyone standing under object.
D
Pulleys
224A
Drop black ropes
Organizer plates
H-28375A
Organizer pulleys
H-52010
Advertisement
Table of Contents
Related Manuals for Harken Hoister SUP
Summary of Contents for Harken Hoister SUP
-
Page 1: Important Safety Information
7808: 45 lb (20 kg) System Harken, Inc. • N15W24983 Bluemound Rd, Pewaukee, WI 53072-4974 • Tel: 262-691-3320 • Fax: 262-701-5780 • Email: hoister@hoister.com • Web: www.hoister.com WARNING! Strictly follow all instructions to avoid an accident, damage to property, personal injury or death. See www.harken.com/manuals for additional safety information. WARNING! This product is not to be used for human suspension. -
Page 2: Maintenance And Warranty
INSTALLATION OVERVIEW STEP 1 DETERMINE HOISTER LOCATION PIGTAIL PIGTAIL STEP 2 INSTALL MOUNTING BOARDS LAG SCREW LAG SCREW STEP 3 INSTALL PIGTAIL LAG SCREWS STEP 4 INSTALL ROPE ORGANIZER 2" x 6" x 7" RISER BOARD ORGANIZER STEP 5 ASSEMBLE HOISTER SYSTEM View STEP 6 OPERATING HOISTER SYSTEM... -
Page 3: Plan The Installation
STEP 1: DETERMINE HOISTER LOCATION A. PLAN THE INSTALLATION STORAGE OPTIONS Measure height of object. Make sure object can be Pull car into garage with object on car rack. stored above or below the open garage door. Above Garage Door: Clearance to lift and store OPTION 1. - Page 4 STEP 1 CONTINUED: DETERMINE HOISTER LOCATION B. PLAN LOCATION OF MOUNTING BOARDS DISTANCE BETWEEN MOUNTING BOARDS Distance between mounting boards should be 1/3 of Mounting boards are used to position Hoister directly object’s length. above object to be lifted. Exception: Distance between mounting boards for long WARNING! Do not screw into laminated rafters.
- Page 5 STEP 2: INSTALL MOUNTING BOARDS A. DRILL CEILING RAFTER ATTACHMENT POINTS B. DRILL MOUNTING BOARD Measure center-to-center distance between rafters. LOCATE CEILING RAFTERS Mark distance on mounting boards. Mark drill points Mounting boards must attach to ceiling rafters (see in the center of the board. Drill "...
-
Page 6: Front View
STEP 3: INSTALL PIGTAIL LAG SCREWS A. DETERMINE PIGTAIL LAG SCREW (B) LOCATION DRILL 2 HOLES ON EACH MOUNTING BOARD PULL VEHICLE INTO GARAGE Drill Hole Drill Hole Pigtail Lag Screw Holes Point Point Object Width MOUNTING BOARD Add 2" (50 mm) outside 2"... - Page 7 STEP 4: INSTALL ROPE ORGANIZER A. MOUNT RISER BOARD AND DRILL HOLES B. ASSEMBLE ROPE ORGANIZER IMPORTANT! Use smaller drill bit in this step. Organizer Plates Organizer Pulleys Washer Lag Bolt Washer DIAGRAM 9 Lag Bolt Mount 2" x 6" x 7" riser board on front mounting board cen- tered between the two Pigtail Lag Screws (B).
- Page 8 STEP 5 CONTINUED: ASSEMBLE HOISTER SYSTEM B. ATTACH PULLEYS Place one Pulley (D) on each Pigtail Lag Screw (B). Ceiling Front Wall Avoid installing Welded Screw Eye above tall DIAGRAM 13. shelves. Rope must point down to lock. ATTACH BLOCK AND TACKLE (G) INSTALL WELDED SCREW EYE (A) ON FRONT WALL Attach Block and Tackle system (G) to welded Screw Eye (A) with Shackle (C).
-
Page 9: Install Rope
STEP 5 CONTINUED: ASSEMBLE HOISTER SYSTEM GARAGE DOOR C. INSTALL ROPE POSITION WEBBING STRAPS Place object in position under system. Place Webbing PULLEY PULLEY Straps (E) under object to be lifted. Push buckles together to lock. Long Long Drop Drop Rope Rope CEILING... - Page 10 STEP 6: OPERATING HOISTER SYSTEM B. STORE OBJECT WARNING! Disable garage door opener when installing, raising, or lowering the Hoister. Do With object in raised position make sure Single Black/ not raise or lower with anyone standing under Red Hoisting Rope (F) is securely locked in cleat with rope object.
-
Page 11: Maintenance
MAINTENANCE WARRANTY WARRANTY MAINTENANCE Inspect rope (H and F), knots and straps (E) regularly What Is Covered – This warranty covers defects in for signs of chafe, wearing or UV damage. Replace materials or workmanship. immediately. Inspect knots for signs of slipping. When Who Is Covered –... - Page 12 Each Hoister kit is complete and simple to install. Easy one-person operation with a single control rope. Self-locking cleat grips instantly if accidentally released. Do not use this product for human suspension. SELECT THE HARKEN HOISTER YOU NEED: Lifting Weight 1. Determine maximum Part...
Need help?
Do you have a question about the SUP and is the answer not in the manual?
Questions and answers