Advertisement
Quick Links
BEFORE YOU BEGIN
BEFORE YOU BEGIN
·
Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
·
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
·
These instructions contain important care, cleaning,
and warranty information-
instructions for the consumer.
·
Make sure that the bath and the finished wall
material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
·
Before starting the door installation, lay out and
identify all the parts. Use the exploded view
illustrated on page 2 for reference.
·
For the installation method of customized shower
with different dimensions, please refer to this
instructions.
CAUTION: Risk of injury or product damage.
Tempered glass cannot be cut, drilled or knocked
by hard object. Make sure corner area of the
glass refraining from knocking so as to cause
personal injury due to broken glass.
ATTENTION:
Please install this door on Kohler
receptors or curbs. (Not included). If the curb is not
Kohler-branded, please note its top width should fall
within the range of 50~80mm.
IMPORTANT:
The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won t take responsibility of the installation
quality.
1120770-T01-C
please leave these
·
·
·
·
·
·
)
13-1
-1-
MATTIA
INSTALLATION INSTRUCTIONS
PIVOT DOOR, L-SHAPE
2
50~80mm
3mm/m
528437
Copyright Kohler China Ltd., 2010
L
K-36971T
(
, 2010
Advertisement
Related Manuals for Kohler MATTIA K-36971T
Summary of Contents for Kohler MATTIA K-36971T
- Page 1 · · All information is based on the latest product information available at the time of publication. Kohler China Ltd. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. · ·...
-
Page 2: Parts Identification
ROUGHING-IN Unit: mm K-36971T 900-1000 700-1000 1870-2000 B 15 PARTS IDENTIFICATION PARTS IDENTIFICATION Track Side Panel Door Panel Assembly Wall Channel Sealing Strip Cover Strip Sealing Strip Cover Strip 1120770-T01-C... -
Page 3: Installation Requirements
Top Caps Glass Fixing Clamp Fixing Bolt Spacer Glass Fixing Cover Door Handle Assembly 4mm Allen Key Cover 3mm Allen Key Cover Cap Spacer Splashguard INSTALLATION REQUIREMENTS INSTALLATION REQUIREMENTS Tools Required · · Phillips Screwdriver · · Pencil · · Caulk Gun ·... -
Page 4: Installation
INSTALLATION NOTE LH version shown. RH fitting is a mirror image of these instructions. DOOR SIDE The door must be Mark the wall 20mm in from the installed with the pivot front edge of the tray on both by the wall, not the sides. - Page 5 Carefully lift the door assembly into place. PANEL SIDE Mark the wall 20mm in from the front edge of the tray on both sides. 20mm Caution The line on the wall jamb marks the maximum amount of adjustment. When fitted this line MUST NOT visible outside the wall channel.
- Page 6 Break one spacer in half. Have a person stand inside the enclosure. Carefully lift the panel into place. Caution Place the 3mm section into the base of the wall channel. STEP STEP Fix the panel to the door at top and bottom. Carefully slide the panel into the wall channel.
- Page 7 Remove the pivot base of the top track. Lift the door into place. Locate the bottom pivot pin into the collar, the insert into the pivot base. IMPORTANT: Ensure the door is fully supported at all times. Caution STEP STEP Fit the pivot base into the top pivot pin, and tighten it Check that the door and panel are far enough into onto the top track with the screws.
- Page 8 If the tray has been fitted level the gap under the On the door side turn the adjusters through 90 to lock glass panel should be 3mm along its length and the the door assembly to the wall channel. bottom track should be on the tray. The position of the door can be adjusted by loosening the fixing screws 'A' and undoing the locks in the...
- Page 9 Fit the seals to the side of the door and the side of Fit the cover strip to the wall jamb. the panel. Note: The cover strip may need cutting to the correct length, but do not stretch when fitting. When the door is closed the magnetic strips should touch along their length.
- Page 10 Slide the covers over the glass fixing clamps top and Lay a thin bead of sealant between wall channel and bottom. wall on both sides. STEP STEP Lay a thin bead of sealant along the bottom of track Fit the door handle. and fill the gap between the glass and tray on the outside of the enclosure.