Advertisement
Quick Links
Advertisement
Related Manuals for VIRTUFIT Ultimate Pro 2
Summary of Contents for VIRTUFIT Ultimate Pro 2
- Page 1 Ultimate Pro 2 Ergometer Rowing Machine For any questions regarding the product you can contact Fitness Benelux: Twekkelerweg 263 +31 (0)74-7600219 Fitness 7553 LZ Hengelo service@fitnessbenelux.nl Benelux Nederland www.fitnessbenelux.nl Uw partner in fitness...
-
Page 2: Table Of Contents
CONTENTS Safety Instructions Assembly Parts Note Assembly Steps 6-11 Part Overview Part List 13-14 Ultimate Pro 2 Ergometer Rowing Machine... -
Page 3: Safety Instructions
Additional terms and conditions are listed in the back of this manual or enclosed owner’s manual. Colors and specifications subject to change without notice. Ultimate Pro 2 Ergometer Rowing Machine... -
Page 4: Assembly Parts
ASSEMBLY PARTS (J4)Screw (J2)Washer M10x1.5t (J3)Bolt M6x50mm (J0)M8 Nylon Nut (J1)Bolt M10x16mm M4x12.7mm (J9)Screw (J5)Bol M8x25mm (J6)Bolt M8x16mm (J7)Washer M8x1.5t (J8)Pull pin M4x10mm Ultimate Pro 2 Ergometer Rowing Machine... -
Page 5: Note
PLEASE BE CAUTIOUS as some components may be sharp and can cause harm if not handled correctly. Always use safety measurements when assembling any piece of equipment or machinery. Ultimate Pro 2 Ergometer Rowing Machine... -
Page 6: Assembly Steps
Console Tube (G) to the stem of Base Leg (A). PLEASE BE CAREFUL OF EXPOSED WIRE ENDS. THE WIRES SHOULD RECEDE BACK INTO STEM ONCE CONNECTED IN ORDER TO PREVENT DAMAGE OR DISLOCATION. Ultimate Pro 2 Ergometer Rowing Machine... - Page 7 Railing (B) face down so that the receiving device for the seat cushion is on the floor. Place Rear Base Leg (D) above the pre-screwed holes of the Base Rail (B). Once placed secure with 2 (J1) Bolt(s) and (J2) washer(s). Ultimate Pro 2 Ergometer Rowing Machine...
- Page 8 NOTE: You must install foot pedals before moving forward with the assembly process. Should Step 5 be skipped the Pre-screwed holes on the base railing would cover up the pre screwed holes on the Forward Base leg where the foot pedals are to be installed. Ultimate Pro 2 Ergometer Rowing Machine...
- Page 9 NOTE: Please be sure to tighten and of Forward Base (A) and turn secure ALL BOLTS AND WASHERS clockwise until the bolt is IN THEIR PLACE TO ENSURE A securely fastened SOLID AND SECURE foundation to the rower. Ultimate Pro 2 Ergometer Rowing Machine...
- Page 10 Rail Handle (B21) gently downwards. This will cause Forward Base (A) to drop down and will allow you to raise Base Railing (B) until it clicks securely into a folded position. When you are ready to unfold the VirtuFit Ultimate Pro 2 Ergometer Rowing Machine again, simply pull on PULL PIN (J8) while holding onto Base Railing (B).
- Page 11 ASSEMBLY STEPS Damper Lever Foot Height Adjuster Push down to adjust the position of the heel support. Ultimate Pro 2 Ergometer Rowing Machine...
-
Page 12: Part Overview
PART OVERVIEW Ultimate Pro 2 Ergometer Rowing Machine... -
Page 13: Part List
Nylon Insert Lock Nut Foot Pad RingCover Washer M4*Φ10*1T SensorBracket Tapping Screw M4*10mm Sensor Swivel Axial Hearth Rate Reciever Swivel Axial Socket Φ21.5*12mm Handle Holder Washer 1/2”*2.0T*Φ23 Philip Head Socket Screw M5*10mm Cap Head Socket M10*16mm Screw Ultimate Pro 2 Ergometer Rowing Machine... - Page 14 Cap Head Socket Screw M8*35mm Cap Head Socket Screw M8*16mm Rear Stabilizer Washer M8*Φ16*1.5T Flat Oval End Cap 40*80 Pull pin Foot Pad 40*32mm Ball Head View M4*10mm Tapping Screw M4*12mm Pedal Stable Bucket Ultimate Pro 2 Ergometer Rowing Machine...
- Page 15 Voor vragen of ontbrekende onderdelen kunt u contact opnemen met Fitness Benelux: Twekkelerweg 263 +31 (0)74-7600219 Fitness 7553 LZ Hengelo service@fitnessbenelux.nl Benelux Nederland www.fitnessbenelux.nl Uw partner in fitness...
Need help?
Do you have a question about the Ultimate Pro 2 and is the answer not in the manual?
Questions and answers