Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for NOREMAT AXIONA Series
- Page 1 LAIL OWERS Axiona - Prodigia Left Hand Version Operator’s MANUAL Translation of the operator’s manual original version Book ref : 132524 Index : - Eco-friendly printing on 100% recycled paper. This book contains pictures that are not contractual.
-
Page 2: Table Of Contents
Operator’s manual INDEX INTRODUCTION RECOMMENDATIONS RESPONSIBILITIES OF THE USER GENERAL SAFETY RULES 1. Contact with oil 2. Noise / dust 3. Vibrations 4. Heat 5. Delivery 6. Before fitting to the tractor/cv 7. Before starting the rotor 8. Before leaving the tractor/cv CHAPTER 1 : TECHNICAL CHARACTERISTICS 1. - Page 3 Operator’s manual CHAPTER 2: OPERATION AND MAINTENANCE 1. Description of the machine 2. Identification of the control movement 3. Identification of control 4. Use of the digital controls (Start - Joystick - Initialization - Measures - Hour counter) 5. Operation 5 1 Transport position 5 2 Working position 5 3 Choice of the working ground speed...
-
Page 4: Introduction
Operator’s manual INTRODUCTION Congratulations on acquiring your new side-arm mower/flail-cutter* Model AXIONA - PRODIGIA From it’s introduction, this machine has given the user, greater benefits of ease of operation and operating comfort not found in a rear mounted arm machine. We hope that it will give you the satisfaction that you justifiably expect and that motivated your choice. -
Page 5: Recommendations
NOREMAT will assist you with information and advice. It is recommended that you make contact with a NOREMAT technician to establish your informational and instructional needs in relation to the machine and it’s use. Furthermore, it is desirable that each user can benefit from the experience and expertise of NOREMAT, your Direct-Constructor. -
Page 6: Responsibilities Of The User
Operator’s manual RESPONSIBILITIES OF THE USER The user is responsible to adhere strictly to the safe-use regulations and safety points which are defined in this manual. As with the driving of all machines, the user must match his speed of travel in the transport position or during work, to the condition of the roadway or terrain. -
Page 7: General Safety Rules
Operator’s manual GENERAL SAFETY RULES It is essential to follow the instructions in this manual to ensure the safety of persons operating or in the vicinity of the machine. 1. Contact with oil At the time of oil changes or when working on any components which may retain hydraulic pressure, ALWAYS wear adequate safety equipment Body Gloves... -
Page 8: Vibrations
These daily exposure limit values are precised in the article R 231-119 of the Labour regulation. Noremat carried out trial runs to evaluate the level of vibrations emitted by a tractor /machine unit and transmitted to the operator’s seat. As an indication, the median value recorded is 0.45m/s2 per eight hours base period in normal work conditions as recommended by the manufacturer. -
Page 9: Before Fitting To The Tractor/Cv
Operator’s manual General Safety Rules 6. Before fitting to the tractor/cv -It is necessary that the tractor is equipped with a cab or means of protecting the driver from possible debris thrown from the tool. -Check the condition of the PTO shaft guard on the tractor. -Carefully read the fitting instructions supplied with the drive shaft. -
Page 10: Chapter 1 : Technical Characteristics
50 Arm M45 Arm 850 kg 865 kg 875 kg Maximum tool weight at the end of arm : 300kg, except with written permission from NOREMAT. 1.3- PERFORMANCES 4.5 m 5.0 m L Maximum lateral reach* 4.5 m * 5.0 m * V Vertical reach 5.6 m *... -
Page 11: Transport Of The Machine By Lorry
It is essential to lock the arm with the locking kit (blue supports) supplied with the machine. Contact NOREMAT who can supply you with the correct locking kit. For safety reasons, the equipment is delivered in the ‘delivery’ position. In this position, machine movements are locked by supports that serve both for lifting the machine and for anchoring it to the lorry. -
Page 12: Unloading
Technical Characteristics Unloading : □ Lift the machine with the help of a suitable gantry crane (fork truck : use only if the necessary kit is fitted to the machine) □ Move clear of the lorry and fit the adjustable stands to the machine. □... -
Page 13: Attachment Of The Machine To The Tractor/Cv
Increase the engine speed for several minutes. This is very important in PROGRESSIVELY to the figure given by temperatures of less than 5 degrees C. your NOREMAT technician at the time of installation/test Increase the engine speed PROGRESSIVELY to the figure given by ... -
Page 14: Safety Instructions
Technical Characteristics 5. Safety instructions Before using your mower/flail-mower it is important to read these safety rules. □ Ensure that the operator knows and understands the operation of the machine and tractor. The two have to be operated simultaneously what requires practice. If this is not the case, the operator should choose a piece of flat ground without people or obstacles on it to practice. -
Page 15: Chapter 2: Operation And Maintenance
:Js13 Date: 6 - Transfer link bracket Fax: 0 Echelle :1:20 7 - Angle transfer bracket Ce plan est la propriété de la société NOREMAT peut être reproduit ou communiqué sans son auto Format: A3 Matière: Désignation : VOIR... -
Page 16: Identification Of The Control Movement
Operation and Maintenance 2. Identification of the control movement Digital control Digital control* Digital control** 3 proportional 4 proportional 2 proportional movements movements movements 1B 1A option : Thumbwheel for the head proportional movement (4A/4B) Axiona - Prodigia... -
Page 17: Identification Of Control
Operation and Maintenance 3. Identification of control Option B light Power up light Green = correct battery Orange = low battery Float light Red = polarity inversion Ignition Display Rotor direction light Accumulator switch Rotor direction selection Float switch Emergency stop Option B switch Fault indicator light Rotor switch... - Page 18 Before forcing the start, check the reason of the error by looking the events list and try to fix it. The 256 last events are viewable by browsing with the buttons + and -. In case of problem, take contact with your NOREMAT technician/dealer to organize a visit. Axiona - Prodigia...
- Page 19 Operation and Maintenance JOYSTICK INITIALIZATION It is necessary to initialize the joystick when it’s replaced or one of the components (thumbwheel). To do this, the user access code (1111) has to be previously entered. SET UP JOYSTICK CANCEL INIT. KEEP IN NEUTRAL AND CONFIRM .D8 Move the joystick and the MOVE PROP...
- Page 20 Operation and Maintenance MEASURES (D EpENDINg ON OpTION It is possible to make some measures coming from the different sensors fitted on the machine. MEASURES Options HOUR COUNTER BATTERY VOLTAGE OIL T° OIL PRESSURE MEASURE .CO MEASURE .C2 MEASURE .C4 See details page 23 VOLTAGE .C1...
- Page 21 Operation and Maintenance HOUR COUNTER It is possible to reset the daily counter. Thanks to the software, you can check the rotor working time since last reset («ROTOR TIME .L2», ), the time before doing the next service/maintenance («NEXT SERVICE .L4», ) or the total rotor working time («ROTOR TOTAL .L5», MEASURES...
-
Page 22: Operation
Operation and Maintenance 5. Operation 5.1- Transport position Make sure the mowing head is locked in its bracket. Fig 1 As indicated on figure 1, transport height is : A : 2,65 m + the X height (distance between ground and frame of the machine). -
Page 23: Description Of The Machine
Operation and Maintenance 6. Description of the machine 6.1- MACHINE PRESSURES ADJUSTMENT 190 bars 125bars 160 bars 140 bars 210 bars 210 bars 210 bars Priming pump supplying rotor pump : 18 bar (+ or - 3 bar) Movement hydraulic circuit (valve block) : 210 bar (axiona), 345 bar (prodigia) Rotor hydraulic circuit : 210 bar (axiona), 345 bar (prodigia) *These pressures are set at the factory. -
Page 24: Greasing
The guarantee of long service life and correct operation depends on strict observation of the greasing intervals. It is essential to use good quality grease. We recommend that you use a Multi-purpose Extreme Pressure grease of type L-XBDH2 (NOREMAT ref 102475). -
Page 25: Pto Driveshaft Greasing
Operation and Maintenance 7 3 PTO driveshaft greasing Follow recommendations on greasing (see page 10.1) Greasing points (red arrows) As will all operations, follow the safety rules (see p.13). Clean and grease the PTO shaft. Grease protections during winter Frequency : grease every 8 hours of work (see stickers on the transmission). The working life of the transmission depends on the way it is maintained. -
Page 26: Oil Changes
First oil change at 300 hours and every 1500 hours afterwards. At least, at the beginning of every season. Oil tank capacity : 80 litres of oil NOREMAT HV46 (ref : 108357). Procedure : - clean the area around the filler cap and remove the cap. -
Page 27: Oil Filter Cartridge Replacement
AXIONA: Capacity of gearbox : 0.5 liter of oil, NOREMAT 80W90 (ref: 102466) PRODIGIA: Capacity of gearbox : 1 liter of oil NOREMAT 80W90 (ref: 102466) Procedure : - clean the area around the breather on top of dust and debris and remove it. -
Page 28: Maintenance
Operation and Maintenance 9. Maintenance 9.1- DAILY MAINTENANCE □ Using a compressed air line at a maximum pressure of 6 bar blow air through from inside to outside. Brush the outside face of the radiator. □ Clean under the head linkage transfer bracket. □... -
Page 29: Attachment Of The Machine To The Tractor/Cv
□ Mount the machine side stabilisers >>HG and HD>> to the upper position of the tractor’s multi-position hitch frame, if sufficiently strong, or use a Noremat bracket. □ Adjust and fit the lower end of the stabilisers to the chassis jaws. -
Page 30: Storage
In order to improve the stability the track width should be increased. In order to check the stability of your attachment, would you please contact your NOREMAT Dess : Tolérance générale sauf... - Page 31 1. The front weight (s) (fitted or not with additional weight(s) must in all cases be within the recommendations of the tractor manufacturer 2. Your NOREMAT technician can advise you on the type of tyres and the pressure required also with the weight of the wheels used.
-
Page 32: Warranty
JURISDICTION CLAUSE : For any disagreement or dispute arising between the buyer and NOREMAT relative to the performance or interpretation of the present warranty contract, the only competent jurisdiction will be that of the Meurthe and Moselle Department (County), number 54, in which the NOREMAT registered office is located. -
Page 33: Notes
Operation and Maintenance Notes ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................Axiona - Prodigia...