Samsung AllShare Cast Dongle Quick Start Manual

www.samsung.com
Graphics used in this manual are for illustration purposes. The actual products may vary.
Overview
Status indicator
HDMI socket
Make sure you have the following items: AllShare Cast Dongle, travel adapter, HDMI A-to-A
cable, and user manual. The supplied items may vary.
Using the AllShare Cast Dongle
You can view your mobile device's screen on a monitor.
Use the mobile device supporting the AllShare Cast or Screen Mirroring feature, and the
monitor supporting HDMI(High Definition Multimedia Interface) feature and HDCP(High-
bandwidth Digital Content Protection) feature. Some devices may not be compatible.
1
Connect the AllShare Cast Dongle to a power outlet using the travel adapter. The indicator turns
red after 3 to 4 seconds.
2
Connect the AllShare Cast Dongle to a monitor using the HDMI A-to-A cable. The red indicator
begins blinking after approximately 30 seconds.
• For information about connecting the HDMI cable, refer to the monitor's user manual.
• The mobile device cannot connect to the AllShare Cast Dongle, unless the AllShare Cast Dongle is
connected to a monitor.
3-1
To connect to a new mobile device, use one of the following methods. The PIN code method is not
supported on some mobile devices.
• Reset button method (complete steps within 2 minutes)
Press the Reset button. The indicator turns blue. On the mobile device, launch AllShare Cast or
Screen Mirroring. The monitor displays the AllShare Cast Dongle's name. Select the same name
from the list that is displayed on your mobile device.
AllShare Cast Dongle
GH68-37002P
Type B. 05/2013. Rev. 1.2
Reset button
Power socket
- 1 -
• PIN code method (complete steps within 30 seconds)
On the mobile device, launch AllShare Cast or Screen Mirroring. The monitor displays the AllShare
Cast Dongle's name. Tap and hold the same name from the list that is displayed on your mobile
device. Check the PIN code displayed on the monitor, and enter the PIN code on your mobile device.
3-2
To connect to a previously used device (complete steps within 2 minutes):
On the mobile device, launch AllShare Cast or Screen Mirroring. The monitor displays the AllShare
Cast Dongle's name. Select the same name from the list that is displayed on your mobile device.
4
When the connection is complete, the monitor displays the mobile device's home screen.
• The screen aspect ratio on your device should be identical with that of the monitor. Otherwise, part
of displayed screen may be cut off. For better picture quality, set the screen aspect ratio on your
monitor to fit its original screen or select the auto aspect ratio setting manually. If auto aspect ratio
setting is not available on your device, some parts of screen can be cut off.
5
To connect to a new device, press and hold the Reset button until the indicator turns red, and then
release. Repeat this setup procedure from step 3.
Make sure the AllShare Cast Dongle is connected to a power outlet.
．
AllShare Cast Dongle supports monitors up to 1080p. The supported resolution may differ
．
depending on the connected mobile device.
When an error occurs while in use, disconnect the travel adapter and connect it again.
．
AllShare Cast or Screen Mirroring automatically terminates when a headset or a
．
Bluetooth headset is connected to the mobile device during video playback. However, it
stays connected when playing games or using the Internet
Safety Precautions
Keep your device dry
Humidity and all types of liquids may damage device parts
of electronic circuits.
Do not use or store your device in dusty, dirty
areas
Dust can cause your device to malfunction.
Avoid exposing your device to very cold or very
hot temperatures (below 5 °C or above 35 °C)
Extreme temperatures can cause the deformation of
the device and reduce the charging capacity and life of
your device.
Do not drop your device or cause impacts to
your device
If bent or deformed, your device may be damaged or parts
may malfunction.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Users are not permitted to make changes or modify the device in any way.
Changes or modifications not expressly approved by Samsung will void the user's authority to
operate the equipment.
Do not disassemble, modify, or repair your device
Any changes or modifications to your device can void your
manufacturer's warranty. For service, take your device to a
Samsung Service Centre.
When cleaning your device:
Wipe your device with a towel or an eraser. Do not use
chemicals or detergents.
Do not use the device for anything other than its
intended use
Avoid using your device's light close to the eyes of
children or animals
Use only Samsung-approved adapters
Unauthorised or Non-Samsung chargers could cause
damage to your device or in extreme circumstances an
explosion, it could also invalidate any warranty on the
product.
- 2 -