Summary of Contents for H-2 Technik Z-004
- Page 1 Z-004 Manual Z-004 ZigBee Module Manual H-2 Technik UG (haftungsbescgränkt) www.h-2technik.com Rhode-Island-Allee 49, Karlsruhe, Germany D-76149 +49 721 6624655/+49 1797087228...
-
Page 2: Table Of Contents
Z-004 Manual Version Information Version Date Modified By Introduction 10.2016 Timo Release Inhalt Overview ............................3 The detailed parameters of Module ..................... 3 Module parameters ......................3 Pin description........................4 PCB mechanical design ......................6 Factory setting ........................6 Format of AT setting command .................... -
Page 3: Overview
Z-004 Manual 1. Overview Z-004 ZigBee wireless module is designed with TI CC2530F256 that is a true system-on-chip (SOC) solution for IEEE 802.15.4 ZigBee applications, the module can be widely used in short distance wireless communication field, with low power consumption, small volume, strong anti- jamming capability. -
Page 4: Pin Description
Z-004 Manual 2.2 Pin description To use Z-004 ZigBee as transparent transmission module，you only need to focus on the function and use of the following pin, it can directly interact with external serial devices, to implement ZigBee wireless communication. - Page 5 Z-004 Manual Rhode-Island-Allee 49, Karlsruhe, Germany D-76149 +49 721 6624655/+49 1797087228...
-
Page 6: Pcb Mechanical Design
Z-004 Manual 2.3 PCB mechanical design 2.4 Factory setting Every parameter of the module is configurable via PC or AT command. Rhode-Island-Allee 49, Karlsruhe, Germany D-76149 +49 721 6624655/+49 1797087228... -
Page 7: Format Of At Setting Command
Z-004 Manual 3. Format of AT setting command The “AT” command format is “0x5a+0xaa+cmd+len+data”, the head of the command frame is 5a aa, cmd is the command self, len is the data length and the data is the user data. -
Page 8: Setting Parameters
Z-004 Manual Note: The modules can join into the configured network automatically and save all parameters when power off. If the device wants to join into other network, please clear its network information using ”0x02” as “Data”. 3.2 Setting parameters... -
Page 9: Querying Parameters
Z-004 Manual Querying parameters To query parameters saved in module using 0xBx, command format is: 5a+aa+cmd Rhode-Island-Allee 49, Karlsruhe, Germany D-76149 +49 721 6624655/+49 1797087228... -
Page 10: Command Data Transmission
Z-004 Manual Command Data Transmission The module transmits data transparently. If the module receives data from UART interface, it can send out data in Broadcast,Unicast,Multicast mode. To setting transmission mode using following command: Rhode-Island-Allee 49, Karlsruhe, Germany D-76149 +49 721 6624655/+49 1797087228... -
Page 11: Pc Software Setting
Z-004 Manual 4 PC Software Setting In addition to using AT command configuration method, you can also use PC configuration software, which is provide in CD. Install the software and open it, as the follow picture shows Configure UART parameters and open UART port. - Page 12 Z-004 Manual If UART connection is successful, module parameters can be queried. After the query is ran successfully, in log windows you will see the current parameters. Rhode-Island-Allee 49, Karlsruhe, Germany D-76149 +49 721 6624655/+49 1797087228...
- Page 13 Z-004 Manual Set/Select module parameters and click the button “Set”. If setting is OK, in log windows you will see the values that has been set. There are three function buttons, “Restore the default setting” -> to Restore default setting “Reset”->Reboot the module, “Clear the Network Info”->Clear the network information.
-
Page 14: Visualizing Zigbee Network
Z-004 Manual 5 Visualizing ZigBee network Z-004 is compatible with TI’s Z-Sensor Monitor, which is provided in CD. The complete relevant ZigBee network topology can be viewed by this software. Firstly, connect the device to the PC via UART. Secondly, install the Z-Sensor Monitor software. Here is an example, one coordinator module and three router modules. - Page 15 Z-004 Manual Connect any one of them to the PC via UART. Open Z-Sensor Monitor and choose the right UART parameters. Pull down the P0.1 to the GND, after that topology of network can be investigated and shown: Rhode-Island-Allee 49, Karlsruhe, Germany D-76149...
-
Page 16: Transparent Data Transmission
Z-004 Manual As the picture shows, the 01℃ means the count of getting topology of network, “0x3A94” means the short address of the module, “09:40:11” means the time of getting topology of network. 6 Transparent data transmission Users can test transparent transmission between nodes. - Page 17 Z-004 Manual Open PC serial assistant, setting baud rate as well as serial port. From now on, two modules can communicate with each other via UART. Rhode-Island-Allee 49, Karlsruhe, Germany D-76149 +49 721 6624655/+49 1797087228...
-
Page 18: Typical Application Circuit Connection
Z-004 Manual 7 Typical application circuit connection Z-004 module is supplied with firmware that means user can use it as an ordinary serial device. Transparent transmission can be done very easily using following circuit connection. Rhode-Island-Allee 49, Karlsruhe, Germany D-76149...