Installation - Barthelme CHROMOFLEX PRO FILE Instruction Manual

INSTRUCTION
MANUAL
FOR
CHROMOFLEX PRO
FILE
PLEASE READ THIS MANUAL CAREFULLY
AND KEEP IT IN A SAVE PLACE!
2. TECHNICAL DATA CV
Operating voltage: 8 V to 26 V DC
Protection class: III
Measures without antenna (L | B | H):
37 | 13 | 8 mm
Output current:
1 channel: max. 3 A | channel
2 channels: max. 1.5 A | channel
3 channels: max. 1 A | channel
4 channels: max. 1 A | channel
WARNING 1:
LED light may have very high intensity
even when dimmed. Some modern LEDs
are classified by the lasers marking ob-
ligation. Particularly in connection with
optics also weak LEDs may be very dan-
gerous. Staring into LEDs may cause irre-
parable damage to the eye's retina. Hence:
NEVER STARE INTO THE BEAM. Use diffu-
sers to spread the intensity!
WARNING 2:
Please be aware of the fact that LED light
may cause side effects. This light changes
intensity very fast! Changing light may af-
fect the perception and is
Item.-No. 66000341 CV – 1-channel
66000342 CV – 2-channel
66000343 CV – 3-channel
66000344 CV – 4-channel
1. USAGE
CHROMOFLEX Pro series was designed so
that sophisticated illuminations in the field
of decoration and wellness can be attained
even without programming. The unit is
equipped with various colour effects by
default such as: colours, calming colour
changes, even show effects. Some of them
can be edited or set as standard effects by
radio control.
For control and settings either CHRO-
MOFLEX Pro Glas Touch RGBW (item.-
No. 66000336,66000337), CHROMOFLEX
Pro remote control (item.-No. 66000045),
CHROMOFLEX Pro Wallswitch (item no.
66000373) or CHROMOFLEX Pro USB
3. SAFETY INSTRUCTIONS
The modules might produce some heat.
Care must be taken to provide unrestric-
ted air ventilation.
The unit is equipped with a limited protec-
tion against reverse polarity. Connecting
the power in reverse polarity can destroy
the module, even if connected for a short
time only.
Important: It is guaranteed by design that
the units will never generate any higher
voltage than the supply voltage. The modu-
le is the ideal solution for use in low-volta-
ge areas, like pools, steam baths, SPAs, etc.
Electronics must not be modified. Observe
the official regulations for electrical de-
vices (like DIN, VDE, EN), especially when
LEDs are used in wet areas!
This product is not a toy, keep away from
children!

4. INSTALLATION

The electric wiring/connection must
comply with all current and valid nati-
onal requirements, be constructed by a
certified electrical tradesman, and com-
ply with all the requirements set forth in
this planning manual.
Attention: Disconnect the system and
the device before beginning any work!
dongle (for PC/ item no. 66000036) are
necessary.
The modules were designed for indoor use
in dry places. The LEDs might also be used
in wet environments or outdoors, if suited
for that purpose. For outdoor use we also
offer optional housings.
IMPORTANT: The modules must be ope-
rated with a power supply that is matched
to the used LEDs! Non-LED loads (especi-
ally inductive loads like motors, coils, etc.)
might damage or destroy the module.
If any of the before mentioned points is not
observed short circuit or electric shock
might occur.
CHROMOFLEX Pro series operates on a
frequency of 868.3 MHz (licence-free in EU,
Switzerland, Norway and Iceland).
We decline any liability, loss or damage
caused by improperly used modules!
Guarantee is also lost in such cases.
LEDs can get quite hot. We strongly re-
commend ensuring maximum operating
temperature is not exceeded, because this
might reduce the expected life time of the
LEDs significantly.
4.1 ASSEMBLY SITE
The unit is suitable for assembly in pro-
files, it is important not to shield the an-
tenna, it can affect wireless signal range.
In operation the unit might produce heat.
Care must be taken to provide unrestric-
ted air ventilation.