Operation; Maintenance; Optional Accessories; Protecting The Environment - DeWalt D25820 Original Instructions Manual

English
3. Set the mode selector switch
only" position.
4. Twist the chisel until it locks in position.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.

WARNING: Tool chisels may be hot and gloves should
be worn when changing or removing them to avoid
personal injury.

WARNING:
• Be aware of the location of pipework and wiring.
• Apply only a gentle pressure to the tool (approximately
20 kg). Excessive force does not speed up chiseling but
decreases tool performance and may shorten tool life.
• Always hold the tool firmly with both hands and
ensure a secure stance. Always operate the tool with
the side handle properly assembled.
nOTE: Operating temperature is -7˚ to +40˚ C (19˚ to 104˚ F).
Using the tool outside of this temperature range will decrease
the life of the tool.
Proper Hand Position (Fig. E)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the
side handle , with the other hand on the main handle
3
Switching On and Off (Fig. A)
To turn the tool on, press the on/off rocker switch
lower part of the trigger.
To stop the tool, press the on/off rocker switch at the upper part
of the trigger.
Chipping and Chiselling (Fig. A)
1. Insert the appropriate chisel and rotate it by hand to lock it
into one of 18 positions.
2. Set the mode selector switch
only position.
3. Fit and adjust the side handle
4. Turn the tool on and start working.
5. Always turn the tool off when work is finished and
before unplugging.
6
to the "hammering
2
.
4
1 at the
to the hammering
2
3 .

MAINTENANCE

Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Brushes
The carbon brushes are not user-serviceable. Take the tool to an
authorized D WALT repair agent.
e
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.

Optional Accessories


WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.

Protecting the Environment

Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
WALT recommended
e