Advertisement
Page 8 of 12
NOTICE DE MONTAGE
•
Pour monter la grille de protection sur la moto, couper la mousse autocollante fournie en
bandeaux de 10mm puis collez les au bas du cadre de protection radiateur, de façon à ce qu'ils
se placent entre la grille de protection radiateur et le radiateur (svp, espacez-les de façon égale
autour du cadre de protection radiateur car ils empêcheront la protection de toucher le
radiateur).
•
Enlever le boulon du côté droit de la moto, voir Photo 1.
•
Enlever le rivet à l'arrière du panneau, voir photos 2 et 3, en poussant au milieu du rivet pour
le libérer.
•
Enlever le panneau de carénage, en le tirant doucement pour le libérer, voir photo 4.
•
Répéter les étapes précédentes de l'autre côté de la moto.
•
Une fois le radiateur exposé, desserrer les 2 boulons indiqués sur la photo 5, pour créer un
espace de 3mm entre le radiateur et le carénage, voir photo 6.
•
Répéter l'étape précédente de l'autre côté de la moto.
•
Monter la grille en position, en veillant à ce que les 4 onglets de fixation se placent sur les
boulons, puis fixer le radiateur en place en serrant les 4 boulons selon les valeurs de serrage
recommandées.
•
Remonter les 2 carénages.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer's statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they
were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be
in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the
gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No
returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not
refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1
14/09/2018 (LF)
CONSUMER NOTICE
R&G
www.rg-racing.com
8
RAD0234
Email:
info@rg-racing.com
Advertisement
