Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Tyre ?are T650
Summary of Contents for Tyre ?are T650
- Page 1 Instruction Manual Wireless tire pressure and temperature monitoring system...
-
Page 2: Table Of Contents
U901T 出厂设置 Contents 1. Product introduction ………………………………………….. Introduction(LCD display description ) …………. 2.Factory settings ………………………………………………….… 3.Parameters setting ………………………………………….……. · Pressure unit setting..............· Temperature unit setting............· Pressure alarm value setting............. · Temperature alarm value setting..........· Tire matching setting..............·... -
Page 3: Product Introduction
1.Product introduction Monitor Solar panel USB interface Button positions Buttons: “ ” :Press and hold the - button to turn on or turn off.Select function. “SET”:Press and hold the SET button to enter setting mode or save and exit to standby after finish setting. :Selection button. -
Page 4: Introduction(Lcd Display Description)
Introduction(LCD display description) Icon and description Solar energy charging(Display while sunlight exposure to solar panel ) Abnormal alarm(Alerts when tire pressure, temperature,sensor battery is abnormal) Matching sensor with monitor Exchange tire location Monitor battery display Temperature unit(℃ or ℉） Pressure unit(BAR or PSI) Press and hold the - button for 3-6s to turn on. -
Page 5: Factory Settings
2.Factory settings 产品介绍 Default Parameters： Pressure Unit BAR/PSI High Pressure 6.0BAR(87PSI) 4.0BAR(58PSI) Low Pressure ℃/℉ Temperature Unit Temperature alarm value 65℃/149℉ Relationship among pressure units PSI,kg/cm²,kPa and BAR 1BAR=14.503PSI 1BAR=1.0197 kg/cm2 1BAR=100kPa Changing Parameters： Press and hold SET for 3s to enter the factory setting mode, There are 6 groups of settings that can be reset,as follows: 1. - Page 6 3.Parameters setting Tire pressure alarm value setting The tires in monitor interface are divided into two axles as follows: The tire numbers(01.02,03,04,05,06) represent the tire position where the sensor is located. ① First axle ② ③ ④ Second axle ⑤ ⑥...
- Page 7 Parameters setting Pressure unit setting n the standby interface,press and hold SET to enter into the setting mode, press + to select to "BAR PSI" interface ,press SET then press + or - to select pressure unit you want. And press the SET to confirm setting,finally press and hold SET for 3 seconds to save the setting and exit to standby.
- Page 8 Parameters setting High pressure alarm value setting of the first axle In the standby interface,press and hold SET to enter into the setting mode. Press + to select to setting interface "HI"on first axle as below. Press SET then press + or - to select high pressure alarm value you want. And press SET to confirm setting ,finally press and hold SET for 3 seconds to save the setting High pressure alarm value setting interface of the first axle Low pressure alarm value setting of...
- Page 9 Parameters setting High pressure alarm value setting of the second axle In the standby interface,press and hold SET to enter into the setting mode. Press + to select to setting interface "HI" on second axle as below.Press SET then press + or - to select high pressure alarm value you want. And press SET to confirm setting ,inally press and hold SET for 3 seconds to save the setting and exit to standby.
- Page 10 Parameters setting High temperature alarm value setting In the standby interface,press and hold SET to enter into the setting mode. Press + to select to setting interface "HI" as below.Press SET then press + or - to select high temperature alarm value you want. And press SET to confirm setting ,finally press and hold SET for 3 seconds to save the setting High temperature alarm value setting interface Tire matching...
- Page 11 Parameters setting Tire interchange setting Press and hold the SET to enter setting mode,press + button to“ “,press SET to start setting.After this,SET as a selection button to select the tire you need to exchange.Then press + and - to adjust the tire NO. to the tire location you want.(Press SET directly to pass if don't need to exchange) {Ex:01 exchange to 02.Press + from 01 to 02 then press SET to confirm.
-
Page 12: Function
4.Function When tire pressure and temperature exceeding the user-defined safety range,the corresponding parameters and fault icons on the monitor screen will flash,accompanied by alarm sound. You can press any button to cancel the alarm sound ,but the fault icon remains on and flashes until all tire failures are removed. （High temperature alarm/Low power alarm：Interface switch to pressure after alarming 8s and switch to temperature/low power alarm interface automatically after 8s.Rrpeat the switching until... - Page 13 Function High temperature alarm When the temperature of the front left tire is 66℃（exceeding user set value)the monitor will display as below,accompanied by alarm sound. Air leakage alarm When the sensor detects tire leakage of the front left ,it will send the leakage data to the monitor immediately,the monitor will display as below, accompanied by alarm sound.
-
Page 14: Internal Sensor Installation
5.Internal sensor installation Pull out the original valve,cleaning the residue... - Page 15 Internal sensor installation Sensor installation Fixed the sensor with the spanner and lock with screw cap...
- Page 16 Internal sensor installation Adjust the angle Fixed the sensor after sensor angle correct and lock it with spanner...
- Page 17 Internal sensor installation Re-inflate after finishing the tire and wheel hub. Do dynamic balance and match lead.
-
Page 18: Internal Sensor Parameter
6.Internal sensor parameter 外置传感器更换电池说明 Sensor specification Working humidity：100% Weight：TJ：48g（without valve30g） Size：TJ：60mm*30mm*15mm（length*width*height) Battery life：2~3years（Can be used 2~3 years while drive 3-4 hours a day） Basis：CTB160109001Q (Test report is used by legal qualification of testing institutionstitutions） Pressure testing range：0 ~ 8 BAR (0 ~ 116 PSI) Temperature testing range：-40℃... -
Page 19: Notice And Statement
7.Notice and statement ·Product is only suitable for car series pressure range within 8 BAR. ·Safety of car tyre can not be relied on products all. Driver should periodically check the tires，make sure the tire puncture, cut, drum kits and other injury - free. ·When product warn ,car should be stopped as soon as possible and deal with it.
Need help?
Do you have a question about the T650 and is the answer not in the manual?
Questions and answers
I have extra sensors from a extra set I have. Batteries are good followed the match a replacement sensor but not working. I have the 6 tyres TPMS 5 of the original are working but lost 1 Thanks
To troubleshoot a non-working Tyre ?are T650 TPMS sensor using extra sensors, follow these steps:
1. Check Battery: If the monitor shows "LO" for the sensor's position, the sensor battery is low. Replace the sensor with an extra one.
2. Match Sensor with Monitor: Use the “Tire matching setting” in the factory setting mode to pair the new sensor with the correct tire position.
3. Exchange Tire Location: If needed, use the “Interchange tire setting” to update the sensor position in the monitor after replacing or moving sensors.
4. Re-inflate and Balance: After installing the new sensor, re-inflate the tire and perform dynamic balancing.
To enter factory setting mode, press and hold the SET button for 3 seconds. Use the settings to match or reset the sensor connection.
This answer is automatically generated