Related Manuals for CONTACLIP EMS-eco
Summary of Contents for CONTACLIP EMS-eco
-
Page 1: Operating Instructions
EMS - Easy-Marking-System EMS - eco Operating Instructions Release: July 21, 2010 ©... -
Page 2: Table Of Contents
1. Introduction....................3 2. Items supplied ....................4 3. Product overview ..................5 4. Set-up ......................6 5. Operation......................7 6. Cleaning and product care .................10 7. Accessories....................11 8. Troubleshooting ..................12 9.Technical information...................13 10. Instructions for packaging the plotter EMS-eco ........14 11. Safety instructions ..................15... -
Page 3: Introduction
1. Introduction: Thank you for purchasing the EMS-eco, a flexible plotter that helps you label marking elements quickly and easily. Rugged construction in stylish aluminium Labelling area A4 size 220 mm x 305 mm Easy to change fixtures to suit a variety of marking elements Auto calibration no adjustment necessary Capable of labelling marking elements up to 10.5 mm in height. -
Page 4: Items Supplied
Please check you have received all the items supplied with your labelling device (see list below). Please retain the packaging in case you need to return the device. The following items are supplied as standard: 1. Plotter EMS-eco 2. Power supply with corresponding mains power cord 3. USB cable 4. Operating instructions... -
Page 5: Product Overview
3. Product overview Segment 2 Segment 1 1) Plotting area 2) Pins for holding support plates 3) Clip adapter for plotter pen 4) Penholder 5) Power supply 6) USB port 7) Control panel/control keys 8) Writing arm 9) Plotter pen storage location 10) Interface for optional external devices... -
Page 6: Set-Up
Do not expose the system to direct sunlight. Please ensure that the connections on the right-hand side of the device are accessible at all times. Position the EMS-eco firmly on the work surface where it is to be used, ensuring it is level. -
Page 7: Operation
PC. Clear buffer If the EMS-eco contains data the yellow light will come on. You can delete this data by pressing the 'Clear buffer' key. To do this the system must be in stop mode (red light on). - Page 8 'ON' to start the plotter. To re-activate the signal please use the same sequence. Insert the plotter pen into the pen holder Before using the EMS-eco, insert the plotter pen with the desired tip width into the clip adapter of the pen holder. Important: Only plotter pens of the types shown with HP-adaption may be used.
- Page 9 Placing the fixtures on the Plotter EMS-eco There are four pin stops on the plotting area where up to two different fixtures can be loaded. Different fixtures are available depending on the size of the marking elements. They can occupy one or two segments on the plotting area.
-
Page 10: Cleaning And Product Care
6. Cleaning and product care Protect the EMS-eco from dust and other dirt. When not in use, cover the plotter. A special dust cover is available as an accessory. Wipe the device occasionally after use with a dry, lint-free cloth or a mild cleaning agent. -
Page 11: Accessories
7. Accessories available in six tip-widths Refill- Plotter Pen Pen holder Ink Cartridges available in six tip-widths Disposable- Plotter Pen Cleaning Set Pen Cleaner Cleaning Fluid Dust Protection Cap... -
Page 12: Troubleshooting
8. Troubleshooting If your plotter EMS-eco is not functioning correctly, please check the following: Device fails to switch on Check whether the mains plug and connecting plug are plugged in correctly. Check whether the socket being used is functioning properly. Is the green light of the power supply illuminated? If not, please replace the power supply. -
Page 13: Technical Information
9. Technical Information EMS-eco plotter specifications Type of plotter: Flatbed plotter Maximum plotting area: 220 mm x 305 mm Plotting speed with pen: Max. 40 mm/s Plotter pen: Special plotter pens with HP fixing Ports: USB Level 1.1 Control language:... -
Page 14: Instructions For Packaging The Plotter Ems-Eco
10. Instructions for packaging the plotter EMS - eco two corner pieces with inlay center piece covering the y-arm two corner pieces without inlay inside the white inside the white box complete accessory box... -
Page 15: Safety Instructions
11. Safety instructions Safety instructions ● Keep the operating instructions in a safe place. ● This device complies with all recognised technical standards and all relevant safety regulations. ● The mains power supply used must correspond with that specified on the name plate. - Page 16 Instructions de sécurité ● Conserver ces instructions dans un endroit sûr. ● Cet appareil répond aux normes techniques et satisfait toutes les règles de sécurité. ● Le courant utilisé doit être identique à celui spécifié sur l'appareil. ● Ne pas utiliser cet appareil dans un environnement humide. ●...
Need help?
Do you have a question about the EMS-eco and is the answer not in the manual?
Questions and answers