Subscribe to Our Youtube Channel
Related Manuals for Advantech EPD-132
Summary of Contents for Advantech EPD-132
- Page 1 User Manual EPD Control Board EPD-132 Development Wireless ePaper Display Solution...
- Page 2 No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
- Page 3 Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defec- tive, it will be repaired or replaced at no charge during the warranty period. For out- of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight.
- Page 4 LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following "Contains TX FCC ID: M82-EPD-132-092 ". If the labelling area is larger than the palm of the hand, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part...
- Page 5 XXXyyyLPDzzzz-x」 字樣。 Technical Support and Assistance Visit the Advantech website at http://support.advantech.com where you can find the latest information about the product. Contact your distributor, sales representative, or an Advantech customer ser- vice center for technical support if you need additional assistance. Please have the following information ready before you call: –...
- Page 6 The equipment has been dropped and damaged. The equipment has obvious signs of breakage. DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. EPD-132 Development Kit User Manual...
- Page 7 Equipment L'équipement est tombé et a été endommagé. Equipment L'équipement présente des signes évidents de rupture. AVERTISSEMENT: Cet ensemble d'instructions est donné conformément à la norme CEI 704-1. Advantech décline toute responsabilité quant à l'exactitude des déclara- tions contenues dans le EPD-132 Development Kit User Manual...
- Page 8 EPD-132 Development Kit User Manual viii...
-
Page 9: Table Of Contents
Introduction ....................2 Specifications .................... 2 Figure 1.1 Block Diagram ............4 System Implementation................4 1.3.1 Advantech EPD-132 Development Kit .......... 4 Chapter Development Kit HW Specification ..5 Figure 2.1 Module Outline: 108 x 122 x 3.9 mm......6 Figure 2.2 Module connection to panel........7 Board level I/O .................. - Page 10 Download Images to EPD-132 &REFLASH IMAGE....41 3.5.3 EPD-132 Carousel Mode............42 3.5.4 EPD-132 Firmware Update............43 3.5.5 Upgrade Firmware to EPD-132 and connect to ePaper manager .. Chapter WISE-EC EPD Design-in Service ..47 The Acquisition of Information ..............48 4.1.1 Design..................
- Page 11 Chapter Introduction...
-
Page 12: Chapter 1 Introduction
Introduction The EPD-132 is a development kit with development tools which support the ultra- low power 2.4GHz RF wireless protocol integrated with the 13.3" R/B/W & B/W EPD in an ARM Cortex-M4 processor. Users may use this kit to experience how wireless modules deliver images to e-Paper and how e-Paper displays images. - Page 13 Image needs to be set as 1600*1200 pixels, do not resize it after completing the image as this will cause jaggy edges. 24-bit / BMP format for EPD-132B 24-bit / BMP format for EPD-132R, color range values below. Red: (255,0,0) Black: (0,0,0) White (255, 255, 255) EPD-132 Development Kit User Manual...
-
Page 14: System Implementation
1.3.1 Advantech EPD-132 Development Kit This architecture is composed of TFTP server, Tera Term, and EPD-132 (ePaper and controller). Physically, the development kit uses ED22 to connect between the control host computer and the EPD-132 module. Users control EPD-132 module through Tera Term on the host computer, so the image can be delivered wirelessly to ePaper when the user executes the command in Tera term. -
Page 15: Chapter 2 Development Kit Hw Specification
Chapter Development Kit HW Specification... -
Page 16: Figure 2.1 Module Outline: 108 X 122 X 3.9 Mm
This section provides board level PCBA design in #3.1 and the system level refer- ence design in #3.2. EPD-132 PCBA has the following spec. PCBA: 108 x 122 x 3.9 mm PCB thickness: 3 mm ± 10% ... -
Page 17: Figure 2.2 Module Connection To Panel
Humidity: 60% RH+-10%RH, Non-condensing Note! If the panel module has been in low temperatures between 0~-25 °C for a while, we recommend to leave it between 20 to 30 °C for 4 days before assembly. EPD-132 Development Kit User Manual... -
Page 18: Board Level I/O
39 pins FPC to connect to e-paper panel ALERT 10 pins FFC to connect to daughter board FFC_GPIO 10 pins FFC connector for external GPIO DEBUG 10 pins FFC connector SWTEST For software test PWR_ON1 4 pins DIP Switch EPD-132 Development Kit User Manual... -
Page 19: Cn2
2.1.1 Table 2.2: CN2 PIN_NAME USB_D- USB_D+ EPD-132 Development Kit User Manual... -
Page 20: Cn3
2.1.2 Table 2.3: CN3 PIN_NAME EPD-132 Development Kit User Manual... -
Page 21: Cn8
SIMO, MTSR - corresponds to MOSI on both master and slave devices, con- nects to each other. SDI, DI, DIN, SI - on slave devices; connects to MOSI on master, or to below connections. EPD-132 Development Kit User Manual... -
Page 22: Cn9
MISO (or SDI on a master) connects to MISO (or SDO on a slave). Slave Select is the same functionality as chip select and is used instead of an addressing concept. Pin names are always capitalized as in Slave Select, Serial Clock, and Master Output Slave Input. 2.1.4 EPD-132 Development Kit User Manual... -
Page 23: Table 2.5: Cn9
Table 2.5: CN9 PIN_NAME PIN_NAME 2.1.5 EPD connector EPD-132 Development Kit User Manual... - Page 24 SDDO4 (Data) SDDO5 (Data) SDDO6 (Data) SDDO7 (Data) +VCOM (Common connection) +VGH (Positive power supply +VGL (Negative power supply gate driver) gate driver) GDOE_P SPV (Start pulse gate driver) GDCLK (Clock gate driver) +VCOM (Common connection) EPD-132 Development Kit User Manual...
-
Page 25: Daughter Board Connector
2.1.6 Daughter Board Connector Table 2.7: ALERT PIN_NAME PIN_NAME +VMOD LED_2- LED_1- EPD-132 Development Kit User Manual... -
Page 26: Table 2.8: Con21
2.1.6.1 Daughter Board Table 2.8: CON21 PIN_NAME PIN_NAME LED_1 : Green LED_2: Red +VDD SW1 Un-mount, SW3 as below. Table 2.9: SWTEST PIN_NAME PIN_NAME +VDD EPD-132 Development Kit User Manual... -
Page 27: Ffc_Gpio
Table 2.10: LED PIN_NAME PIN_NAME +VDD +VDD LED_1- LED_2- 2.1.7 FFC_GPIO EPD-132 Development Kit User Manual... -
Page 28: Table 2.11: Ffc_Gpio
Table 2.11: FFC_GPIO PIN_NAME PIN_NAME +V3.3 GPIO_0 (default LOW) GPIO_1 (default LOW) GPIO_2 (default LOW) GPIO_3 (default LOW) GPIO_4 (default LOW) GPIO_5 (default LOW) GPIO_6 (default LOW) GPIO_7 (default LOW) GPIO Voltage level is 3.3V EPD-132 Development Kit User Manual... -
Page 29: Debug
2.1.8 DEBUG Table 2.12: FFC_GPIO PIN_NAME PIN_NAME UART1_TX UART1_RX JTAG_TDI JTAG_TDO JTAG_TCK JTAG_TMS JTAG_TRST BOOT_0 +V3.3 EPD-132 Development Kit User Manual... -
Page 30: Swtest
1. TDI (Test Data In) 2. TDO (Test Data Out) 3. TCK (Test Clock) 4. TMS (Test Mode Select) 5. TRST (Test Reset) optional. 2.1.9 SWTEST Table 2.13: SWTEST PIN_NAME PIN_NAME SW_TEST# SW_TEST# EPD-132 Development Kit User Manual... -
Page 31: Pwr_On1
2.1.10 PWR_ON1 Table 2.14: SWTEST PIN_NAME PIN_NAME NC: only for SW testing usage NC: only for SW testing usage EVK_MODE# W_DISABLE: WiFi power on/off BM22 mode EVK mode WIFI power ON WIFI power OFF EPD-132 Development Kit User Manual... -
Page 32: Panel, Pcba Connector And Usb Data Transmission Connector
FPC from the ePaper display Release the rotary latch of the connector on the control board. Blend the FPC carefully to the control board direction. Insert the FPC into the connector on the control board. EPD-132 Development Kit User Manual... - Page 33 After connecting steadily, lock the rotary latch. Check if the connection is correct and tight. Below Item 2: Connected Wi-Fi antenna to mainboard. Below item 5: Connected IO daughter to mainboard. Below item 6: Connected power cable to mainboard USB(CN3). EPD-132 Development Kit User Manual...
-
Page 34: Daughter Board: Led & Button Behavior
Daughter Board: LED & Button Behavior The daughter board: 9696053RS00 works with EPD-132. 2.2.1 Button behavior If the Red LED (LED2) lights up, press the button to turn off LED2. If Red LED (LED2) is off, the user can press the button to change the screen image to next page. -
Page 35: Chapter 3 Epd-132 Development Kit Hands-On
Chapter EPD-132 Development Kit Hands-on... -
Page 36: Components List
EPD-132 development kit helps users to quickly download images and display them on ePaper. Users can download multiple images into the EPD-132 kit and setup the display in carousel mode. The system will then make a slideshow of those images. -
Page 37: System Architecture
Configure Wi-fi setting through BLE BLE-WiFi introduction service is a demo for setting up SSID and password to join the network via smart phone. EPD-132 will be paired via a BLE GATT server with the smartphone.Then you can start Wi-Fi security setting. - Page 38 If the connection is successful, you can see the picture below. Press the CUS- TOM SERVICE button. Note! You need to remove bluetooth pairing with "WiFiInt" from the bluetooth setting when you can not connect to the device. Find the UUID: ACA0EF7C-EEAA-48AD-9508-19A6F6B356 for SSID charac- teristic. EPD-132 Development Kit User Manual...
- Page 39 Find the UUID: 40B7DE33-93E4-4C8B-A876-D833B415A6CE for Password characteristic then proceed as in Step 4. If joining is successful you can see the network IP on the console screen. EPD-132 Development Kit User Manual...
-
Page 40: Prepare Recommended Os
Prepare a Win 7 PC. 3.3.3 TFTP Download /Upload File Make sure PC is connected to 2.4G Wi-Fi. Recommend using tftpd64. After the download is complete, open Tftp64 program, click on setting button (add image figure 3-1). EPD-132 Development Kit User Manual... - Page 41 Then next select TFTP tab. Click on Browse button to specify Base Directory of the TFTP Server. You can select any folder in your windows laptop/PC as the Base Directory. All the files transferred using TFTP Server will be placed in this folder. (Example: D:\TFTP\ADAVANTECH is Base Directory). EPD-132 Development Kit User Manual...
-
Page 42: Python Environment Setup
Python Environment Setup Download and install Python (must use Python 2.7.x Windows x86) Set the variables of Widows environment path: add “C:\Python27;C:\Python27\Scripts” to path Download and install python PIL package Download and unzip picture transformation tool "BmpToPixel_EPD-132R.py" EPD-132 Development Kit User Manual... -
Page 43: Transfer Bmp Image To Epd Format Using Python
Output filename: converted file name (recommend to use "esl" as the exten- sion) Bmp size must comply with EPD resolution 1600 x 1200 Bmp file: mono color/16 color/256 color/24bits bitmap format Ex: BmpToPixel_D73.py EVK_03.bmp EVK_03.esl Type BmpToPixel.bat to use batch conversion in directory. EPD-132 Development Kit User Manual... -
Page 44: Wise-Ed22 Setup
Copy output files to tftp Base Directory. 3.3.6 WISE-ED22 Setup Download and install WISE-ED22 driver. Update WISE-ED22 FW for EPD-132 project. You can reference ED22 Firm- ware Update. Connected to PC via a micro USB cable, the Device Manager will appear mbed Serial Port. -
Page 45: Evaluation Kit Hands-On
User can see the below FPC from the ePaper display. Release rotary latch of the connector on the control board. Blend the FPC carefully to the control board direction. Insert the FPC into the connector on control board. EPD-132 Development Kit User Manual... - Page 46 1. Connected Wi-Fi antenna to mainboard. 2. Connected ED22 board to mainboard via FPC cable. 3. Connected ED22 board to PC via micro USB cable. 4. Connected IO daughter to mainboard. 5. Connected power cable to mainboard USB(CN3). EPD-132 Development Kit User Manual...
-
Page 47: Command Console Setting
Start a serial tool (use tera term in this), and make the communication setting as shown below. You may setup below item. Download Tera term: Tera version: 4.91 Setup your serial com port and baud rate: EPD-132 Development Kit User Manual... -
Page 48: Reset Epd-132
RESET EPD-132 Press "RST" button, shown below, and the system will then start the HW reset. 3.4.4 Launch TFTP Service PC joins Wi-Fi AP, make sure the PC network is the same domain as with EPD-132. EPD-132 Development Kit User Manual... - Page 49 Lunch tftpd64.exe and select "Tftp Server" tab. Check image folder, image file size must be 960000 bytes. Select tftp server IP. EPD-132 Development Kit User Manual...
-
Page 50: Epd-132 Join Wifi Ap
Wi-Fi throughput test Report Bandwidth between specified period bt_wifi start ble-wifi introducer service Information of bt/wifi and joined AP carousel start epd into carousel mode Refer to chapter 3.5.3 set the led light or dark Turn-on/off led EPD-132 Development Kit User Manual... -
Page 51: Command Description
– led 1 0; turn-off led – led 1 1; turn-on led 3.5.2 Download Images to EPD-132 &REFLASH IMAGE A. DOWNLOAD THE IMAGE tftp <ip> <filename> <flash index> [-r] ip: tftp server ip ... -
Page 52: Epd-132 Carousel Mode
-s 1 1095 50 140 240 0 // set S1 (x, y)=(1095, 50), (w, h)=(140, 240), partial update with GC mode – carousel -s 2 215 740 1230 85 0 // set S2 (x, y)=(215, 740), (w, h)=(1230, 85), partial update with GC mode EPD-132 Development Kit User Manual... -
Page 53: Epd-132 Firmware Update
If errors are encountered, a file called "fail.txt" will appear with details. Note that the WISE-ED22 has to contain the correct firmware to enable drag and drop programming Refer to detailed steps in "3.3.6 WISE-ED22 Setup”. EPD-132 Development Kit User Manual... - Page 54 Step2 CN2 USB DOWNLOAD IMAGE to ITE8951 to control EPD Follow steps and pictures below to setup the hardware Connected EPD FPC to mainboard Connected USB cable to mainboard USB2(CN2) Download and unzip HYPERLINK EPD-132R_CLI_tool Click "IT8951_FWVersion.bat" to get EPD panel information EPD-132 Development Kit User Manual...
-
Page 55: Upgrade Firmware To Epd-132 And Connect To Epaper Manager
Download and unzip update tool Copy and replace new binary (separately available) folder to tool directory Setup EPD-132 to develop mode, reference link Execute “Adv.ESL_Tag-BNEPD_132R.bat” batch file After the firmware update is complete, the EPD-132 will reboot EPD-132 Development Kit User Manual... - Page 56 EPD-132 Development Kit User Manual...
-
Page 57: Chapter 4 Wise-Ec Epd Design-In Service
Chapter WISE-EC EPD Design- in Service... -
Page 58: The Acquisition Of Information
The Acquisition of Information Since ePaper is not a plug and play device, Advantech WISE-EC Design-in Services help customers to reduce the time and work involved with designing a new ePaper device. Advantech handles the complexities of technical research and provides hard-... -
Page 59: Design
TX power / mask / RF harmonic tuning / RX sensitivity When a product moves into the design stage, Advantech will supply a design guide of the device for reference as well as Antenna selection & schematic review. The EPD device design guide provides onboard IO definitions and recommendations so cus- tomers can have a clear guideline to follow during their EPD development. -
Page 60: Integration
Advantech's team has a complete total stan- dard HW/SW solution to fine tune performance, driver integration, and application- specific customization. -
Page 61: Contact Information
Warranty Period Advantech branded off-the-shelf products and 3rd party off-the-shelf products used to assemble Advantech Configure to Order products are entitled to a 2 years complete and prompt global warranty service. Product defect in design, materials, and work- manship, are covered from the date of shipment. -
Page 62: Repair Process
(Dead-on-Arrival). The DOA Cross-Shipment excludes any shipping damage, cus- tomized and/or build-to-order products. For those products which are not DOA, the return fee to an authorized ADVANTECH repair facility will be at the customers' expense. The shipping fee for reconstructive products from ADVANTECH back to customers' sites will be at ADVANTECH's expense. - Page 63 "Attn. RMA Service Department". All products must be returned in properly packed ESD material or anti-static bags. ADVANTECH reserves the right to return unrepaired items at the customer's cost if inappropriately packed. Besides that, "Door-to-Door" transportation such as speed post is recommended for delivery, otherwise, the sender should bear additional charges such as clearance fees if Air-Cargo is adopted.
- Page 64 If a product has been repaired by ADVANTECH, and within three months after such a repair the product requires another repair for the same problem, ADVANTECH will do this repair free of charge. However, such free repairs do not apply to products which have been misused, abused, or subjected to unauthorized disassembly/modification;...
- Page 65 EPD-132 Development Kit User Manual...
- Page 66 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2019...
Need help?
Do you have a question about the EPD-132 and is the answer not in the manual?
Questions and answers