Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ehb electronics SMARTdisplay 70
Summary of Contents for ehb electronics SMARTdisplay 70
-
Page 1: Operating Instructions
Operating Instructions ehb SMARTdisplay 70 Service Personnel Version 2.1 The reproduction and distribution of this document as well as utilization and communication of its contents is not permitted unless expressly authorized. Violators are liable for damages. All rights reserved. -
Page 2: Quick Guide
Operating Instructions ehb SMARTdisplay 70 Quick Guide View light sensor LED green, model ehb5443-4 only On/Off button, model ehb5443-4 only display / touch screen Show the Navigation Bar In order to show the navigation bar (touch button menu) double tap the same position on the screen. -
Page 3: Functionality Of The Navigation Bar
ehb SMARTdisplay70 Operating Instructions Functionality of the Navigation Bar settings error list flip page: left flip page: right (backward) (forward) flip page: up (page navigation) © ehb Errors excepted Vers. 2.1 3/22... -
Page 4: Table Of Contents
Disposal of Devices ...................... 7 Operation ........................... 8 Connection ........................8 Switch On/Off ....................... 9 Capacitive on/off button ehb SMARTdisplay 70 (Art.-No. ehb5443-4 only) ....9 Calibration of the Touch Screen ................... 9 Navigation of Pages ....................10 Change of Settings ......................11 Set Brightness and Contrast .................. -
Page 5: General
1. General 1.1 Introduction The ehb SMARTdisplay 70 offers a variety of functions for monitoring and control for all engines and special machines equipped with CAN bus (SAE J1939). The display can be customized application specific using a configuration tool for PC (Windows XP or Windows 7) provided by ehb-electronics gmbh. -
Page 6: Important Notes For The Use
Operating Instructions ehb SMARTdisplay 70 1.3 Important Notes for the Use How to use The device must only be operated with the supplies provided. Use a mild cleaning agent to clean the device. Do not insert any objects that are not designed for the specific purpose into the openings of the unit, as this may cause problems in the electrical components. -
Page 7: Repair Of Devices
Or use our online service for returning the unit: www.ehbservice.de NOTE! ehb electronics gmbh is only liable for proper performance of tasks as well as for the suitable condition of the materials used. Further claims such as compensation for lost profits or compensation for direct or indirect consequential damages such as loss of data are excluded. -
Page 8: Operation
Operating Instructions ehb SMARTdisplay 70 2. Operation 2.1 Connection The device is affixed with four M4 screws using the included high-grade steel bracket. The electrical connection of the device is made via an M-23 plug Pin/Contacts AuxIN2 AuxIN1 Terminal 15... -
Page 9: Switch On/Off
OHC as it is only updated every 12 minutes or so in the flash memory. 2.3 Capacitive on/off button ehb SMARTdisplay 70 (Art.-No. ehb5443-4 only) On-button ehb SMARTdisplay 70 (Model ehb5443-4 only) -
Page 10: Navigation Of
Operating Instructions ehb SMARTdisplay 70 The calibration may be started on a device that has the standard application installed (delivery state). Connect a USB keyboard, then quickly press the ESC button for 4 times. This function may not be available on devices that have installed custom code. -
Page 11: Change Of Settings
ehb SMARTdisplay70 Operating Instructions The left/right soft keys of the navigation bar are used to flip pages within a group. (forward) to change to next page in group. In Group 2 for example, you will reach Page 3 from Page 2, Page 4 from Page 3, and Page 2 from Page 4. (backward) to change to previous page in group. -
Page 12: Set Brightness And Contrast
Operating Instructions ehb SMARTdisplay 70 3.1 Set Brightness and Contrast Touch the button on setup screen. Then you will be able to set the brightness of the screen and adjust the color using the sliders. Note: If grayscale colors appear to be wrong (e.g. with greenish touch or with rough transitions) this is most likely due to unfavorably set display parameters rather than due to a defective display. -
Page 13: Network (Lan) Configuration
ehb SMARTdisplay70 Operating Instructions Set from left to right the year, month, day, hour, minute, and seconds! Touching one of the buttons will open a numeric input dialog. Enter the desired number and accept the input with Enter button. A valid input will then be effective immediately. -
Page 14: Liveview - Diagnostic Tool
Operating Instructions ehb SMARTdisplay 70 The settings are activated when you touch the button and will remain active (also after restart) until you change and save with the next time. Change to information page using the button to verify if a valid IP address is set. „0.0.0.0“ is not valid and will be shown when there is no network connection. -
Page 15: Error List
ehb SMARTdisplay70 Operating Instructions Menu Structure of LiveView Clears all displayed data. Clear Display Start Data Reception Starts the reception and display of data. Stops reception of data. The data will remain in the list until Stop cleared or the window is closed. Saves a .csv file to the USB flash drive. - Page 16 Operating Instructions ehb SMARTdisplay 70 The touch button menu contains in addition to clearing and detailed view four buttons to select a filter: Possible selections are to view entire list, only active errors, errors that are no longer active, or pas- sive errors read from an engine control unit.
-
Page 17: Communication With The Pc
ehb SMARTdisplay70 Operating Instructions Only passive errors will be displayed. Filter „passive errors“ Close Return to settings menu At each boot of the device a new file for the error list is created. This reduces the risk of data loss, in case a file could not be closed properly and the data of the file was lost. -
Page 18: Upload Of A Project / Configuration
Operating Instructions ehb SMARTdisplay 70 6.1 Upload of a Project / Configuration Start the ehb Workbench Open a project Choose „Upload project data…“ in menu „Extras“ Fill dialog fields as shown: Target IP-Address 192.168.1.100 Username Password 2070 Target Config. Directory/NANDFlash/config... -
Page 19: Software Update
ehb SMARTdisplay70 Operating Instructions ATTENTION! A corrupt archive file will be automatically deleted from the USB flash disk (if possible) for safety reasons! 6.3 Software Update Updating the application software is only possible while application is not running. The device is designed so that stopping/terminating of the application is impossible during normal operation. -
Page 20: Wiring Diagram
Operating Instructions ehb SMARTdisplay 70 7. Wiring Diagram 20/22 Vers. 2.1 © ehb Errors excepted... -
Page 21: Technical Specification
ehb SMARTdisplay70 Operating Instructions 8. Technical Specification Parameter Condition Limits Comment Min. Max. Supply Voltage UB 12...24V Noise Voltage at UB 6Vss, 50Hz Voltage peaks at UB 200V Current consumption at < 5mA The current consump- ignition (off) tion in operation UB 8-24V 350 mA depends on wiring and... -
Page 22: Document Information, History
15.10.2012 Layout 08.09.2014 Adaption Pkt. 2.1, Pkt. 7. 03.02.2015 hag, Kle Adaption Pkt. 2.1. 15.04.2015 Mx, hag Adaption to ehb SMARTdisplay 70 03.12.2016 07.12.2016 Layout Adaption product photo 26.06.2017 Adaption Information to use and Reverence to test standards 24.01.2018 Hk/hag...
Need help?
Do you have a question about the SMARTdisplay 70 and is the answer not in the manual?
Questions and answers