All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by JH 0868 BU TV Consumer Care...
EN 2 PB52.1HU LA Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview Index of this chapter: 1.1.3 Multimedia 1.1 Technical Specifications 1.2 Connections Supported file formats : JPEG 1.3 Chassis Overview : MP3 : Slideshow (.alb) Notes: •...
Page 3
Technical Specifications, Connections, and Chassis Overview PB52.1HU LA EN 3 Connections HDMI 2 SERVICE HDMI 1 AUDIO IN RS 232 AV 1 S-VIDEO DATA 1 AUDIO IN SPDIF 12 13 I_17501_106.eps 060808 Figure 1-1 Connection overview Note: The following connector color abbreviations are used 7.
Page 4
EN 4 PB52.1HU LA Technical Specifications, Connections, and Chassis Overview 10. Cinch: Audio - In 15. HDMI 1, 2: Digital Video, Digital Audio - In Rd - Audio - R 0.5 V / 10 kohm Wh - Audio - L 0.5 V...
Page 5
Technical Specifications, Connections, and Chassis Overview PB52.1HU LA EN 5 Chassis Overview Note: Figure below can deviate slightly from the actual situation, due to the different set executions. SMALL SIGNAL MAIN BOARD SUPPLY PANEL SYSTEM INTERFACE PANEL KEYBOARD CONTROL PANEL IR LED PANEL I_17500_062.eps...
• Use only lead-free soldering tin Philips SAC305 with order the mass of the set by a wristband with resistance. Keep code 0622 149 00106. If lead-free solder paste is required, components and tools also at this same potential.
Directions for Use PB52.1HU LA EN 7 2.3.5 Alternative BOM identification MADE IN BELGIUM MODEL 32PF9968/10 It should be noted that on the European Service website, 220-240V 50/60Hz “Alternative BOM” is referred to as “Design variant”. 128W VHF+S+H+UHF PROD.NO: AG 1A0617 000001 BJ3.0E LA...
EN 8 PB52.1HU LA Mechanical Instructions 4. Mechanical Instructions Index of this chapter: Notes: 4.1 Cable Dressing • Disassembly instructions below are based on the 32” 4.2 Service Positions model, but is comparable for all other models. 4.3 Assy/Panel Removal •...
Page 9
Mechanical Instructions PB52.1HU LA EN 9 Figure 4-2 Cable dressing 32”...
Page 10
EN 10 PB52.1HU LA Mechanical Instructions Figure 4-3 Cable dressing 37”...
Page 11
Mechanical Instructions PB52.1HU LA EN 11 I_117501_107.eps 060808 Figure 4-4 Cable dressing 42”...
Page 12
EN 12 PB52.1HU LA Mechanical Instructions Figure 4-5 Cable dressing 42” Full HD...
Page 13
Mechanical Instructions PB52.1HU LA EN 13 Service Positions 4.3.3 IR & LED Board 1. Release the clip on the right side of the panel by pushing it For easy servicing of this set, there are a few possibilities sidewards. created: 2.
Page 14
EN 14 PB52.1HU LA Mechanical Instructions 4.3.6 Main Supply Panel 1. Unplug connectors. 2. Remove the fixation screws. 3. Take the board out, be careful, it hinges from the left side. When defective, replace the whole unit. 4.3.7 Small Signal Board (SSB) and Tuner Bolt-on Refer to next figures for details.
Page 15
Mechanical Instructions PB52.1HU LA EN 15 I_17500_067.eps 180408 Figure 4-12 SSB...
Page 16
EN 16 PB52.1HU LA Mechanical Instructions 4.3.8 LCD Panel Refer to figure “LCD Panel” for details. 1. Unplug the LVDS connector [1]. Caution: be careful, as this is a very fragile connector! 2. Unplug the connectors [2]. 3. Remove the fixation screws [3] and [4].
Service Modes, Error Codes, and Fault Finding PB52.1HU LA EN 17 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: Specifications 5.1 Test Points 5.3 Service Modes Table 5-1 SDM default settings 5.4 Stepwise Start-up 5.5 Service Tools Default 5.6 Error Codes...
Page 18
EN 18 PB52.1HU LA Service Modes, Error Codes, and Fault Finding 5.3.2 Service Alignment Mode (SAM) Changing the display option via a standard RC: Key in the code “062598” directly followed by the “MENU” button and “XXX”, where XXX is the 3 digit decimal display code (see table Purpose “Option code overview”...
Page 19
Service Modes, Error Codes, and Fault Finding PB52.1HU LA EN 19 How to Navigate occur, the rest of the buffer is empty (00). See also • In SAM, you can select the menu items with the “CURSOR paragraph “Error Codes” for a description.
Page 20
EN 20 PB52.1HU LA Service Modes, Error Codes, and Fault Finding program number is displayed. See DFU on how to change this item. • Location. Gives the last status of the location setting as set via the installation menu. Possible values are “SHOP”...
Page 21
Service Modes, Error Codes, and Fault Finding PB52.1HU LA EN 21 Stepwise Start-up due to overvoltage. It is recommended to measure first the FET 7U08 on short-circuit before activating SDM via the service pads. There are two possible situations: one for protections detected...
Page 22
EN 22 PB52.1HU LA Service Modes, Error Codes, and Fault Finding Off/Stby to Semi Stand by or Protection Mains is applied Standby Supply starts running. All standby supply voltages become available . action holder: MIPS action holder: St-by st-by µP resets...
Page 23
Service Modes, Error Codes, and Fault Finding PB52.1HU LA EN 23 The supply fault line is an OR SUPPLY-FAULT I/O line Supply fault error function of DCDC, DCDC5050 is High? and POD/CI supply switch. Enable the supply fault detection algorithm Set I²C slave address...
Page 24
EN 24 PB52.1HU LA Service Modes, Error Codes, and Fault Finding switch off the remaining DC/DC Log power-ok error and enter Power-ok display high ? converters protection Switch POD-MODE and ON-MODE 3-th try? I/O line high. Reset the Pacific by pulling LOW the Pacific hardware reset line during 100ms.
Page 25
Service Modes, Error Codes, and Fault Finding PB52.1HU LA EN 25 action holder: AVC action holder: St-by autonomous action Semi Standby Wait until previous on-state is left more than 2 seconds ago. (to prevent LCD display problems) Assert RGB video blanking...
Page 26
EN 26 PB52.1HU LA Service Modes, Error Codes, and Fault Finding action holder: AVC Active action holder: St-by autonomous action Mute all sound outputs via softmute Wait 100ms Set main amplifier mute (I/O: audio-mute) Force ext audio outputs to ground...
Page 27
Service Modes, Error Codes, and Fault Finding PB52.1HU LA EN 27 Semi Stand by action holder: MIPS action holder: St-by autonomous action If ambientlight functionality was used in semi -standby (lampadaire mode), switch off ambient light *) If this is not performed and the set is...
Page 28
EN 28 PB52.1HU LA Service Modes, Error Codes, and Fault Finding action holder: MIPS action holder: St-by autonomous action Log the appropriate error and set stand-by flag in NVM Redefine wake up reasons for protection state and transfer to stand-by µP.
Introduction The error code buffer contains all detected errors since the last ComPair (Computer Aided Repair) is a Service tool for Philips time the buffer was erased. The buffer is written from left to Consumer Lifestyle products. and offers the following: right, new errors are logged at the left side, and all other errors 1.
Page 30
EN 30 PB52.1HU LA Service Modes, Error Codes, and Fault Finding code and not the actual cause (e.g., a fault in the protection • Error 5 (PNX85xx doesn’t boot). Indicates that the main detection circuitry can also lead to a protection).
Service Modes, Error Codes, and Fault Finding PB52.1HU LA EN 31 The Blinking LED Procedure Remark on the Supply Errors The detection of a supply dip or supply loss during the normal playing of the set does not lead to a protection, but to a cold 5.7.1...
Page 32
EN 32 PB52.1HU LA Service Modes, Error Codes, and Fault Finding Fault Finding and Repair Tips Fault Finding • Symptom: +1V2 not present (even for a short while, approximately 10 ms) Read also paragraph “Error Codes” -> “Error Buffer” -> “Extra 1.
Page 33
Service Modes, Error Codes, and Fault Finding PB52.1HU LA EN 33 5.9.5 SSB Replacement Follow the instructions in the flowchart in case you have to exchange the SSB. See figure “SSB replacement flowchart”. START Set is still operating? Activate SAM and save the TV settings via “Upload to USB”...
• The above overview of the NAND Flash shows the content 2. Press the “OK” button on a Philips DVD RC-6 remote of the different partitions. It also shows which part of the control (it is also possible to use the TV remote in “DVD”...
Page 35
Service Modes, Error Codes, and Fault Finding PB52.1HU LA EN 35 5.10.3 Stand-by Software Upgrade There are two methods now to upgrade stand-by software: Upgrade via USB In this chassis it is possible to upgrade the Stand-by software via a USB stick. The method is similar to upgrading the main software via USB.
Page 36
EN 36 PB52.1HU LA Service Modes, Error Codes, and Fault Finding Personal Notes: E_06532_012.eps 131004...
Block Diagrams, Test Point Overview, and Waveforms PB52.1HU LA Block Diagram Video VIDEO T01B MAIN TUNER B02A PRO: IDIOM PNX85xx B03F PNX85xx: DIGITAL B09D FPGA 1080p: I/0 BANKS B10C PACIFIC 3 B10A PACIFIC 3: LVDS 7T57 VIDEO OUT/LVDS TDA9897HL/V2 7H00...
Block Diagrams, Test Point Overview, and Waveforms PB52.1HU LA Block Diagram Control & Clock Signals CONTROL + CLOCK SIGNALS B11C DRAM B11A CONTROL STI7101 B11B STI7101: FLASH B11H I2C ADDRESS - 4A (WRITE) B12B IBOARD PNX85xx B02A PRO: IDIOM T01A...
Block Diagrams, Test Point Overview, and Waveforms PB52.1HU LA Supply Lines Overview SUPPLY LINES OVERVIEW SUPPLY B09A DC / DC B09E B11G B03A PNX85xx: POWER B05B AUDIO: PROTECTION / MUTE CONTROL IR LED DEBUG +3V3 +3V3 +5V-STANDBY +5V-STANDBY +3V3 +3V3...
Circuit Diagrams and PWB Layouts PB52.1HU LA SSB: SRP List Explanation Example Personal Notes: 1 . 1 . Introduction Net Name Diagram +12-15V AP1 (4x) +12-15V AP4 (4x) SRP (Service Re ference Protocol) is a softw are too l that creates a list w i th all refer e n c es to signal lines. The list contains...
Page 141
Circuit Diagrams and PWB Layouts PB52.1HU LA SSB (with HC Diversity): SRP List Explanation Example Personal Notes: 1 . 1 . Introduction Net Name Diagram +12-15V AP1 (4x) +12-15V AP4 (4x) SRP (Service Re ference Protocol) is a softw are too l that creates a list w i th all refer e n c es to signal lines. The list contains...
Page 142
Circuit Diagrams and PWB Layouts PB52.1HU LA SSB (with HC Diversity): SRP List Part 1 Netname Diagram PCI-AD13 B03D (1x) POWER-OK-DISPLAY B09A (1x) RxP3oE+_G8 B10A (1x) TUN-FE-DATA3 B02A (2x) TXOC+ B10C (1x) PCI-AD13 B08A (1x) PSEN B03B (2x) RxP3oE+_G8 B10C (1x)
Page 143
Circuit Diagrams and PWB Layouts PB52.1HU LA SSB (with HC Diversity): SRP List Part 2 Netname Diagram 27MHZ-3V3 B11A (2x) CRX0- B06B (1x) DDR2-D29 B03E (2x) EMI-A(13) B11B (2x) IR-out-iB B12B (1x) 2V5-LMI B11C (6x) CRX0- B06C (1x) DDR2-D3 B03E (2x)
Page 161
Alignments PB52.1HU LA EN 161 8. Alignments Index of this chapter: 8.1 General Alignment Conditions Description Test Point Min. Typ. Max. Supply 8.2 Hardware Alignments +3V3-standby FU86 +3.15 +3.30 +3.45 DC-DC 8.3 Software Alignments +1V2-standby FU85 +1.20 +1.25 +1.30 DC-DC 8.4 Option Settings...
EN 162 PB52.1HU LA Alignments • Repeat this step for the other color temperatures that need • Select a COLOUR TEMPERATURE (e.g. COOL, to be aligned. NORMAL, or WARM). • When finished press OK on the RC and then press STORE •...
Page 163
Circuit Descriptions, Abbreviation List, and IC Data Sheets PB52.1HU LA EN 163 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets Index of this chapter: 9.1.1 Features 9.1 Introduction 9.2 Main Supply The main features for this chassis are: 9.3 Abbreviation List •...
Page 164
EN 164 PB52.1HU LA Circuit Descriptions, Abbreviation List, and IC Data Sheets ® ® 9.1.4 Pro:Idiom Technology decrypting ability in the LGDT 1129 series. Pro:Idiom is the leading content protection technology in the hospitality industry and the LGDT 1128A/29 device family makes integration of this...
Circuit Descriptions, Abbreviation List, and IC Data Sheets PB52.1HU LA EN 165 Main Supply Abbreviation List All sets in this chassis come with a buy-in Power Supply Unit 0/6/12 SCART switch control signal on A/V and are a black-box for Service. When defective, a new panel board.
Page 166
EN 166 PB52.1HU LA Circuit Descriptions, Abbreviation List, and IC Data Sheets Monochrome TV system. Sound lines. The fields are written in “pairs”, carrier distance is 6.5 MHz causing line flicker. Dynamic Frame Insertion Infra Red Directions For Use: owner's manual...
Page 167
4.406250 MHz and 4.250000 MHz Sound Intermediate Frequency SMPS Switched Mode Power Supply System on Chip Sync On Green SOPS Self Oscillating Power Supply S/PDIF Sony Philips Digital InterFace SRAM Static RAM Small Signal Board STBY STand-BY SVGA 800x600 (4:3) SVHS...
Page 168
EN 168 PB52.1HU LA Circuit Descriptions, Abbreviation List, and IC Data Sheets IC Data Sheets This section shows the internal block diagrams and pin configurations of ICs that are drawn as “black boxes” in the electrical diagrams (with the exception of “memory” and “logic”...
Page 169
Circuit Descriptions, Abbreviation List, and IC Data Sheets PB52.1HU LA EN 169 9.4.3 Diagram B05C, TPA4411RTJ (IC 7HV0) Pinning Functional Block Diagram (TOP VIEW) TPA4411 SVDD Audio In − R Audio Out − R Short SVSS SGND Circuit SVDD PGND Protection Audio Out −...
Page 170
EN 170 PB52.1HU LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.4.4 Diagram B06C, AD8197A (IC 7J00) Block Diagram Figure 1. TYPICAL APPLICATION 04:20 Pin Configuration AVCC AVCC PIN 1 INDICATOR IN_B0 IP_C3 IP_B0 IN_C3 AVEE AVEE IN_B1 IP_C2...
Page 171
Circuit Descriptions, Abbreviation List, and IC Data Sheets PB52.1HU LA EN 171 9.4.5 Diagram B10B, T6TF4HFG (IC 7GE2) Block Diagram Contrast Reserve Input Proc Contr, Brightness & & Clip Measure MVL manager White-point corr Color LUT Color gamut & Dithering...
Page 172
EN 172 PB52.1HU LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.4.6 Diagram B11A to H, STi7101 (IC7A00) Block Diagram 5 x 2-ch S/PDIF PCM out Peripheral I/O SDRAM AudioL 2-ch and external interrupts AudioR PCM in video in...
Page 173
Circuit Descriptions, Abbreviation List, and IC Data Sheets PB52.1HU LA EN 173 9.4.7 Diagram B11H, SAA7113H/V2 (IC7AD1) MULTI-STANDARD DATA SLICER VBI DATA BYPASS AI11 ANALOG UPSAMPLING FILTER AI1D PROCESSING 12 to 15, VPO7 AI12 19 to 22 OUTPUT bypass FORMATTER...
Page 174
EN 174 PB52.1HU LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.4.9 Diagram T01A, TDA10060 (IC7T18) Block Diagram 54 MHz PSC/SPI host PSC/SPI SLAVE ACQUISITION internal bus MASTER third overtone interface INTERFACE PROCESSOR to all blocks crystal interrupt ATSC 8/16 VSB...
Page 175
Circuit Descriptions, Abbreviation List, and IC Data Sheets PB52.1HU LA EN 175 9.4.10 Diagram T01B, TDA9897HL (IC 7T57) Block Diagram 4 MHz reference input EXTERNAL SOUND BAND-PASS FILTER i.c. ADRSEL GNDD LFSYN2 GNDA EXTFILO EXTFILI FREF OPTXTAL 43, 44 40, 41...
Page 176
EN 176 PB52.1HU LA Spare Parts List & CTN Overview 10. Spare Parts List & CTN Overview For the latest spare part overview, please consult the Philips Service website. Table 10-1 Sets described in this manual: Styling Published in: 26HFL5830D/27...
Need help?
Do you have a question about the PB52.1HU LA and is the answer not in the manual?
Questions and answers