Related Manuals for Kontron CP-RIO6-M
Summary of Contents for Kontron CP-RIO6-M
- Page 1 » User Guide « CP-RIO6-M Dual 2.5" SATA Storage 6U CompactPCI Rear Transition Module Doc. ID: 1031-2494, Rev. 2.0 May 11, 2011 If it’s embedded, it’s Kontron.
-
Page 2: Imprint
Disclaimer Copyright © 2011 Kontron AG. All rights reserved. All data is for information purposes only and not guaranteed for legal purposes. Information has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Kontron and the Kontron logo and all other trademarks or registered trademarks are the property of their respective own- ers and are recognized. -
Page 3: Table Of Contents
CP-RIO6-M Preface Table of Contents Revision History ......................ii Imprint ........................ii Disclaimer ........................ii Table of Contents ...................... iii List of Tables ......................v Proprietary Note ....................... vii Trademarks ......................vii Environmental Protection Statement ................ vii Explanation of Symbols ..................viii For Your Safety ......................ix High Voltage Safety Instructions ................ix... - Page 4 Preface CP-RIO6-M 3.2 Initial Installation Procedures ..............3 - 4 3.3 Standard Removal Procedures ..............3 - 5 3.4 Installation of Peripheral Devices ............3 - 6 3.4.1 Installation of 2.5” HDD/SSD Devices ..........3 - 6 Page iv ID 1031-2494, Rev. 2.0...
- Page 5 SATA Connectors J6 and J7 ..............2 - 3 Rear I/O CompactPCI Connectors rJ3, rJ4 and rJ5 ........ 2 - 4 Placement of the 2.5” SATA HDDs/SSDs on the CP-RIO6-M ....3 - 6 CP-RIO6-M Main Specifications .............. 1 - 6 Standards for the CP-RIO6-M ..............
- Page 6 Preface CP-RIO6-M This page has been intentionally left blank. Page vi ID 1031-2494, Rev. 2.0...
-
Page 7: Proprietary Note
Kontron without further notice. Trademarks Kontron, the PEP logo and, if occurring in this manual, “CXM” are trademarks owned by Kon- tron, Kaufbeuren (Germany). In addition, this document may include names, company logos and trademarks, which are registered trademarks and, therefore, proprietary to their respective owners. -
Page 8: Explanation Of Symbols
Preface CP-RIO6-M Explanation of Symbols Caution, Electric Shock! This symbol and title warn of hazards due to electrical shocks (> 60V) when touching products or parts of them. Failure to observe the pre- cautions indicated and/or prescribed by the law may endanger your life/health and/or result in damage to your material. -
Page 9: For Your Safety
However, the life expectancy of your product can be drastically reduced by improper treatment during unpacking and installation. Therefore, in the interest of your own safety and of the correct operation of your new Kontron product, you are requested to conform with the following guidelines. -
Page 10: General Instructions On Usage
CP-RIO6-M General Instructions on Usage In order to maintain Kontron’s product warranty, this product must not be altered or modified in any way. Changes or modifications to the device, which are not explicitly approved by Kontron and described in this manual or received from Kontron’s Technical Support as a special handling instruction, will void your warranty. -
Page 11: Two Year Warranty
As a result, the products are sold “as is,” and the responsibility to ensure their suitability for any given task remains that of the purchaser. In no event will Kontron be liable for direct, indirect or consequential damages resulting from the use of our hardware or software products, or documentation, even if Kontron were advised of the possibility of such claims prior to the purchase of the product or during any period since the date of its purchase. - Page 12 Preface CP-RIO6-M This page has been intentionally left blank. Page xii ID 1031-2494, Rev. 2.0...
-
Page 13: Introduction
CP-RIO6-M Introduction Chapter Introduction ID 1031-2494, Rev. 2.0 Page 1 - 1... - Page 14 Introduction CP-RIO6-M This page has been intentionally left blank. Page 1 - 2 ID 1031-2494, Rev. 2.0...
-
Page 15: Board Overview
6U CompactPCI CPU boards and provides the capability to install two onboard 2.5" SATA HDDs/ SSDs. In order to use the CP-RIO6-M, a special 6U CompactPCI backplane with rear I/O support as well as a compatible and correctly configured CPU board are required. The CP-RIO6-M con- nects to the backplane via three CompactPCI connectors. -
Page 16: Front Panel
Introduction CP-RIO6-M 1.2.2 Front Panel Figure 1-2: CP-RIO6-M Front Panel Page 1 - 4 ID 1031-2494, Rev. 2.0... -
Page 17: Board Layout
CP-RIO6-M Introduction 1.2.3 Board Layout Figure 1-3: CP-RIO6-M Board Layout – Front View SATA1 SATA0 ID 1031-2494, Rev. 2.0 Page 1 - 5... -
Page 18: Technical Specification
Introduction CP-RIO6-M Technical Specification Table 1-1: CP-RIO6-M Main Specifications CP-RIO6-M SPECIFICATIONS SATA Two SATA I interfaces implemented as onboard, 22-pin, SATA connec- tors, J6 and J7, for connecting two 2.5" SATA HDDs/SSDs CompactPCI Three CompactPCI connectors, rJ3, rJ4 and rJ5, for connecting the... -
Page 19: Standards
Customers desiring to perform further environmental testing of Kontron prod- ucts must contact Kontron for assistance prior to performing any such testing. This is necessary, as it is possible that environmental testing can be destructive when not performed in accordance with the applicable specifications. -
Page 20: Related Publications
Introduction CP-RIO6-M Related Publications The following publications contain information relating to the CP-RIO6-M. Table 1-3: Related Publications PRODUCT PUBLICATION CompactPCI Systems and CompactPCI Specification 2.0, Rev. 3.0 Boards CompactPCI Packet Switching Backplane Specification PICMG 2.16, Rev. 2.0 Kontron CompactPCI Backplane Manual, ID 24229... -
Page 21: Functional Description
CP-RIO6-M Functional Description Chapter Functional Description ID 1031-2494, Rev. 2.0 Page 2 - 1... - Page 22 Functional Description CP-RIO6-M This page has been intentionally left blank. Page 2 - 2 ID 1031-2494, Rev. 2.0...
-
Page 23: Board Interfaces
Functional Description Board Interfaces 2.1.1 Serial ATA Interfaces The CP-RIO6-M provides two SATA I interfaces implemented on two onboard SATA connec- tors, J6 and J7, used to connect two 2.5” SATA HDDs/SSDs. Figure 2-1: SATA Con. J6 and J7 Table 2-1: SATA Con. -
Page 24: Rear I/O Interface On Compactpci Connectors Rj3, Rj4 And Rj5
2.1.2 Rear I/O Interface on CompactPCI Connectors rJ3, rJ4 and rJ5 The CP-RIO6-M is equipped with three CompactPCI rear I/O connectors, rJ3, rJ4 and rJ5. Warning! To support the rear I/O feature, a 6U CompactPCI backplane with rear I/O sup- port as well as a compatible and correctly configured CPU board are required. -
Page 25: Rear I/O Compactpci Rear I/O Connector Rj3 Pinout
CPU board. These pins MUST NOT be connected to any other power source, either within the backplane itself or within the CP-RIO6-M. Failure to comply with the above will result in damage to the CP-RIO6-M. ID 1031-2494, Rev. 2.0... -
Page 26: Rear I/O Compactpci Rear I/O Connector Rj4 Pinout
CPU board. These pins MUST NOT be connected to any other power source, either within the backplane itself or within the CP-RIO6-M. Failure to comply with the above will result in damage to the CP-RIO6-M. Page 2 - 6... -
Page 27: Rear I/O Compactpci Rear I/O Connector Rj5 Signals
CP-RIO6-M Functional Description Table 2-4: Rear I/O CompactPCI Rear I/O Connector rJ5 Pinout SATA:LED# HT1:TX+ HT1:TX- HT1:RX+ HT1:RX- HT0:TX+ HT0:TX- HT0:RX+ HT0:RX- The following table describes the signals of the rJ5 connector. Table 2-5: Rear I/O CompactPCI Rear I/O Connector rJ5 Signals... - Page 28 Functional Description CP-RIO6-M This page has been intentionally left blank. Page 2 - 8 ID 1031-2494, Rev. 2.0...
-
Page 29: Installation
CP-RIO6-M Installation Chapter Installation ID 1031-2494, Rev. 2.0 Page 3 - 1... - Page 30 Installation CP-RIO6-M This page has been intentionally left blank. Page 3 - 2 ID 1031-2494, Rev. 2.0...
-
Page 31: Safety Requirements
The CP-RIO6-M has been designed for easy installation. However, the following standard pre- cautions, installation procedures, and general information must be observed to ensure proper installation and to preclude damage to the CP-RIO6-M, other system components, or injury to personnel. -
Page 32: Initial Installation Procedures
Failure to comply with the instruction below may cause damage to the CP-RIO6-M or result in improper system operation. 2. Ensure that the CP-RIO6-M is compatible with the CPU board and the backplane prior to installation. 3. Ensure that the SATA devices are properly installed prior to installation. -
Page 33: Standard Removal Procedures
4. Disengage the CP-RIO6-M from the backplane by first unlocking the ejection handles and then by pressing the handles as required until the CP-RIO6-M is disengaged. 5. After disengaging the CP-RIO6-M from the backplane, pull it out of the slot. 6. Dispose of the CP-RIO6-M as required. -
Page 34: Installation Of Peripheral Devices
3.4.1 Installation of 2.5” HDD/SSD Devices Up to two 2.5” HDDs/SSDs may be installed on the CP-RIO6-M via the onboard SATA connec- tors, J6 and J7. During installation it is necessary to ensure that the SATA devices are correctly seated in the onboard SATA connectors and properly secured via the four mounting screws.