Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Allmatic Manuals
  4. Receiver
  5. B.RO X40 DISPLAY
  6. Manual

Allmatic B.RO X40 DISPLAY Manual

4 channels rolling code receiver, with display
Hide thumbs Also See for B.RO X40 DISPLAY:

Advertisement

Quick Links

Download this manual
B.RO X40 DISPLAY
4 channels Rolling Code receiver, with
display.
MADE IN ITALY

Advertisement

loading
Need help?

Need help?

Do you have a question about the B.RO X40 DISPLAY and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Allmatic B.RO X40 DISPLAY

Summary of Contents for Allmatic B.RO X40 DISPLAY

  • Page 1 B.RO X40 DISPLAY 4 channels Rolling Code receiver, with display. MADE IN ITALY...

  • Page 2: Electrical Connections

    DESCRIPTION B.RO X40 Display is a 4-channels Rolling Code receiver compatible with all Allmatic Rolling Code remotes. This device has an easy and intuitive functioning thanks to the display interface and 3 buttons. 4 relay outputs are available with dry contact normally open (N.O.) and/or closed (N.C.).
  • Page 3 LEARNING OF A TRANSMITTER The device has available 3 modality for the learning of a transmitter: • Default learning - press briefl y the UP (+) button for the activation. • Sequential learning - press briefl y the DOWN (-) button for the activation. •...
  • Page 4 3.2 - SEQUENTIAL LEARNING The sequential learning memorizes the single key of a transmitter and it associates the key on the desired output. To the stored key is assigned the DEAD MAN function. The receiver exits from the learning phase after 10 seconds of inactivity or with the multiple press of the DOWN (-) button. This learning is activated also with the press of the hidden key of a stored remote control.
  • Page 5 3.3 - ADVANCED LEARNING The advanced learning memorizes the single key of a transmitter. During the learning phase it is possible to set the parameters of the memorized remote control. See paragraph 4 for more information about single parameters. The receiver exits from the learning phase after 10 seconds of inactivity or with the press of the MENU button. Make sure that the receiver is out from any menu.
  • Page 6 Press and hold the MENU button until the display shows: Enable/disable hte key of the transmitter in the channel 2 with UP (+) and DOWN (-) buttons of the receiver. If the key is enabled, the display shows: Press and hold the MENU button until the display shows: Enable/disable hte key of the transmitter in the channel 3 with UP (+) and DOWN (-) buttons of the receiver.
  • Page 7 It erases from the memory all the memorized transmitters. During this process it is possible to select the type of coding that you want to set to the receiver: - biroL: Rolling Code Allmatic; - sawn: Custom. CHECKING MODE OF THE REMOTE CONTROL It checks if the transmitter is memorized and shows: - the location in the memory;...
  • Page 8 SELECTABLE MENU DESCRIPTION VALUES DEFAULT UNIT min-max PARAMETERS FOR OUTPUTS LiFE LiFE Sub-menu where you can: 1-65535 rtIme - set the activation time of the output with the Timed function or Timed+Delay function (LiFE); - set the delay time for the Timed+Delay function (dLy). 0-255 RESET OF THE PARAMETERS It restores the receiver to default settings.
  • Page 9 4.1.6 rtime - OUTPUT PARAMETERS In this sub-menu, for each relay (r01, r02, r03 o r04) it is possible to change the activation duration (LIFE) and the output delay time (dLy). To change the parameters, please follow the procedure below: Go to the menu item rtime.
  • Page 10 SELECTABLE MENU DESCRIPTION VALUES DEFAULT UNIT min-max REMOVAL OF THE TRANSMITTER It allows the removal of the single transmitter. ENABLING OF THE TRANSMITTER enab ON-OFF It allows to enable or disable the transmitter. MOVING OF THE TRANSMITTER move It allows to move the location where the transmitter has been 000-999 registered in the memory.
  • Page 11 Press and hold the MENU button until the display shows: Enable/disable the transmitter key in the output channel 1 with the UP (+) or DOWN (-) buttons of the receiver. If the button is enabled, the display shows: Press and hold the MENU button until the display shows: Enable/disable the transmitter key in the output channel 2 with the UP (+) or DOWN (-) buttons of the receiver.
  • Page 12 ATTENTION: the short pressure of the MENU button during the parameter selection returns the process to the previous point. For example: the brief pressure of the MENU button in channel 1 enabling menu (the display shows CH01) returns the process to the selection of the function (the display shows F00 or the last function selected).
  • Page 13 • Output active, LED on. • Output active and timed, slow blinking. • Output delayed waiting for activation, fast blinking. The receiver will enter the standby mode after 2 minutes of inactivity. The display shows and the LED OUT are disabled. For exit the mode press briefl...

  • Page 14: Flow Chart

    FLOWCHART 14/20 6-1620020 rev.0 27/10/2015...
  • Page 15 EXAMPLE OF USING 9.1 - EXAMPLE 1 6-1620020 rev.0 27/10/2015 15/20...
  • Page 16 9.2 - EXAMPLE 2 16/20 6-1620020 rev.0 27/10/2015...
  • Page 17 9.3 - EXAMPLE 3 6-1620020 rev.0 27/10/2015 17/20...
  • Page 18 9.3.1 - ENTER SETTING STEP BY STEP • Wired input 1: Press and hold MENU button for at least 1 second. Select the item of the menu param and confi rm the selection by pressing the MENU button for at least 1 second. Select the item of the menu Input and confi...

  • Page 19: Technical Features

    15. Disable the key in the CH01 output and confi rm the selection by pressing the MENU button for at least 1 second. 16. Enable the key in the CH:02 output and confi rm the selection by pressing the MENU button for at least 1 second. 17.

  • Page 20: Made In Italy

    MADE IN ITALY ALLMATIC S.r.l 32020 Lentiai - Belluno – Italy Via dell’Artigiano, n°1 – Z.A. Tel. 0437 751175 – 751163 r.a. Fax 0437 751065 http://www.allmatic.com - E-mail: info@allmatic.com 6-1620020 rev.0 27/10/2015...