Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Satellite PolyPortables Manuals
  4. Toilets
  5. Freedom 4
  6. Assembly instructions manual

Satellite PolyPortables Freedom 4 Assembly Instructions Manual

Portable restroom
Hide thumbs

Advertisement

Quick Links

Download this manual
FREEDOM4
Portable Restroom Assembly Instructions
PN 22541 REV B
- 1 -
5/18

Advertisement

loading
Need help?

Need help?

Do you have a question about the Freedom 4 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Satellite PolyPortables Freedom 4

Summary of Contents for Satellite PolyPortables Freedom 4

  • Page 1 FREEDOM4 Portable Restroom Assembly Instructions PN 22541 REV B - 1 - 5/18...
  • Page 2 FREEDOM 4 ASSEMBLY INSTRUCTIONS PN 22541 REV B - 2 - 5/18...
  • Page 3 PN 22541 REV B - 3 - 5/18...

  • Page 4: Helpful Hints

    INTRODUCTION Satellite portable restrooms must be assembled according to approved assembly procedures. Avoid variations in assembly procedures which could adversely affect product life and warranty. All references to front, left, right, and rear are looking at the door of the unit from the outside. Tools: ●Standard screwdriver •Drill Electric or Cordless Drill...
  • Page 5 Install lift handles on Half panels: 4) Use (6) screws PN 18718 with (6) washers PN 5) Place lift handle PN 22522 on outside of panel with screws PN 18718 11360 on inside of half panel, through 6 pre-drilled through holes in handle. Install (6) washer PN 12382 & (6) nuts PN 16307 on screws using # 3 Phillips Head Driver Bit &...
  • Page 6 Rivet panels (left / right / rear) together in rear corners: Install lift handles on side panels: 12) Rivet panels (left / right / rear) together 13) Rivet panels (left / right / rear) 14) Drill at 6 dimple locations near rear in rear corners.
  • Page 7 Install “Tank option PN 16538” and Vent pipe: 20) Install seat lid PN 10570 (comes with 21) Hold tank against panel while installing 22) Insert vent pipe PN 13796 plastic bolts & nuts) on tank PN 16538. screws (3) PN 13860 from outside of unit in into tank PN 16538 until it Plastic bolt through seat lid hinge into the dimples in left panel shown below using 3/8"...
  • Page 8 28) Install seat lid PN 10570 (comes with 29) Hold tank against panel while 30) Insert vent pipe PN 13796 into plastic bolts & nuts) on tank PN 14508. installing (3) screws PN 13860 from tank PN 14508 until it bottoms out Plastic bolts through seat lid hinges into outside of unit in dimples in left panel against screw.
  • Page 9 36) Make sure front pocket on inside of front is up over 37) In right front facing there are 3 38) Install (3) bolts PN 20883 vertical wall of floor. Front gap between door & right pre-drilled holes in the bottom. With with (3) washers PN 22584 in facing of front should be no more than .250”...
  • Page 10 Install Roof: Install the Decal: 44) Rivet roof to top of front. “First place 45) Rivet roof to front door frame. “Pull 46) Place Decal PN 10394 on right block of wood under bottom of door roof down & transfer drill through holes in facing of front as shown.
  • Page 11 Install Door Closure / Door closure cover: 53) Drill at dimples (4) on inside of left 54) Place door closure bracket PN 21382 on 55) Locate & drill out (2) dimples on facing (pocket for door closure bracket) facing inside of door as shown. Install (2) inside of door to mount door closure using #10 (.193”) [5 mm] Drill bit.
  • Page 12 INSTALL GRAB BAR ON REAR PANEL: 62) Drill at 5 lower dimple & 5 upper vertical “0” locations shown below using #10 (.193”) [5 mm] Drill bit on inside of panel. 2 vertical “0” locations that are used with 2 pre-drilled holes in top of Grab bar PN 22541 REV B...
  • Page 13 Rivet Grab bar to rear panel (from outside of unit): 63) “Place Grab Bar on inside of rear panel, make sure bottom of Grab Bar is resting on vertical alignment ledges 2 per panel, shown above” Outside of rear panel use (2) rivets PN 14427 in 2 vertical “0”...
  • Page 14 ᴑ INSTALL GRAB BAR ON LEFT PANEL: 64) Drill at 5 lower dimple & 5 upper horizontal “ ” locations shown below using #10 (.193”) [5 mm] Drill bit on inside of panel. 2 horizontal “ᴑ” locations that are used with 2 pre- drilled holes in top of Grab bar PN 22541 REV B...
  • Page 15 Rivet Grab bar to left panel (from outside of unit): 65) “Place Grab Bar on inside of left panel, make sure bottom of Grab Bar is resting on vertical alignment ledges 2 per panel, shown above” Outside of left panel use (2) rivets PN 14427 in 2 horizontal “ᴑ”...