Related Manuals for ADEMCO RapidDome
Summary of Contents for ADEMCO RapidDome
- Page 1 RapidDome Dome Owners Operating & Installation Guide Document Code number – Draft 7-7-00...
-
Page 2: Table Of Contents
Table of Contents Safety Instructions Setting up the RapidDome Dome Wiring Details Settings on the RapidDome Dome Top Board Address Settings Coax Telemetry LED on the RapidDome Dome Bottom Board Alarm Settings Alarm / Relay Connections Installing the RapidDome Dome... -
Page 3: Safety Instructions
These products contain static electricity sensitive devices. Please take appropriate precautions when handling. Handle the RapidDome Dome with care, as improper handling may cause irreparable damage to the precision or sensitive parts within this unit. Never point the camera directly towards a bright light source (for example sunlight), or expose the camera to intensive light situations as this may damage the camera pick-up device. -
Page 4: Setting Up The Rapiddome Dome
Wiring Details Mounting The RapidDome Dome is designed for speed of installation and set up and so the wall and ceiling mount brackets are supplied pre-wired. Customer wiring is via an internal terminal block PCB that is located inside the base plastic cover. (See for the location of the terminal block and for the wiring details.) - Page 5 Mounting Options for RapidDome Dome (including detail of the terminal block) TWISTED PAIR UP-THE-COAX CONTROL (Not Used) (Not Used) (Not Used) (Not Used) Twisted (Not Used) Pair Control (Not Used) Video Signal Video Signal Video Ground Video Ground +V (AC)
-
Page 6: Settings On The Rapiddome Dome Top Board
Settings on the RapidDome Dome Top Board In the following section, please refer to below, for the locations on the board. DILSW1 - Jupiter Microsphere protocol, address setting DIL Switch. V C 4 4 5 V3 V C L D2 - Sys OK LED... -
Page 7: Address Settings
Address Settings The addresses for each Dome are set as shown in the table below. Set the Poles on DILSW 1 to the desired position for each address. D I L SW I TC H SETTI N G S D I L SW I TC H SETTI N G S D I L SW I TC H SETTI N G S D I L SW I TC H SETTI N G S D e n o te s th e... -
Page 8: Led On The Rapiddome Dome Bottom Board
Coax Control Up-the-Coax RapidDome Domes do not require an address setting; therefore the settings of positions 1 - 7 on DILSW1 are ignored. Position 8 controls the alarm feature as described in Section 7. LED on the RapidDome Dome Bottom Board In the following section please refer to below for the locations on the board. -
Page 9: Alarm / Relay Connections
Relay 1 will close its contacts. When the alarm time-out has expired the RapidDome Dome will return to its pre-alarm state and Relay 1 will open its contacts (provided no other alarms have been activated and are still timing out). - Page 10 Connector 3 Connector 2 Top View of RapidDome with Alarms The connections on the RJ45 plugs are numbered as shown below. A suitable termination tool will be required to connect to the RJ45 plugs. Contacts Cable Contact Side View of RJ45 Plug The 2 RJ45 connectors are wired as shown in the table overleaf.
-
Page 11: Installing The Rapiddome Dome
80mm 161mm 42mm 82mm 100mm SQ 142mm Mounting Brackets for RapidDome Dome Step Attach the bracket (wall or ceiling type) using fixings which are appropriate for the surface and able to support the weight of the RapidDome Dome (1.1 kg). - Page 12 PUSH UP Fitting the RapidDome Dome into the bracket Fit the M3 CSK safety locking screw into the bracket to lock the RapidDome Dome in place. This is ESSENTIAL for the safe operation of the RapidDome Dome. (The hole for the screw is on the opposite side of the pole to the slot.) Attach the cable cover.
- Page 13 2 h a vl e s sna p to g e th e r Fitting the Cable Covers When the RapidDome Dome is to be fitted to a JD5S80 (80mm) mounting pole, then the hole in the cable cover will need to be aligned with the screw hole in the pole when fitting the M3 CSK safety locking screw as shown below.
-
Page 14: Sample Configurations And Notes For Twisted Pair Installations
(Point ‘A’.) Insert the RapidDome Dome through the ceiling and fit the retaining disk to the back of the RapidDome Dome. (The rear of the ceiling face). Screw down the three M4 Nyloc nuts to lock the RapidDome Dome into place... - Page 15 Sample Configurations and Notes for RS485 Twisted Pair Installations Individual Twisted Pair Output If a single RapidDome is to be connected to an individual twisted pair output, then the link should be fitted across pins 1 and 2 on LK1. This sets the termination to ON. See...
-
Page 16: Technical Specification
LK1 is set correctly. In a chain of RapidDome Domes, the link MUST be fitted across pins 2 and 3 (termination OFF), for all domes in the chain except the final one. The link MUST be fitted across pins 1 and 2 of the last RapidDome Dome, (termination ON). - Page 17 Do not connect shield to RapidDome Dome WARNING – A fault in the wiring can cause all of the RapidDome Domes in the chain to fail or malfunction Use insulated screw terminals or crimps to This distance is to be...
- Page 18 The above rules concerning the use of RS485 must be adhered to so that the control data is not corrupted. Failure to adhere to these rules will seriously reduce the performance of the RapidDome Dome...
Need help?
Do you have a question about the RapidDome and is the answer not in the manual?
Questions and answers