Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Adapter
  5. ATA 186
  6. Instructions for installing

Cisco ATA 186 Instructions For Installing

Hide thumbs Also See for ATA 186:
1
2
3
4
5
6

Advertisement

Quick Links

Download this manual
Installing the Cisco ATA
This section provides instructions for installing the Cisco ATA 186 and Cisco ATA 188. Before you
perform the installation, be sure you have met the following prerequisites:
•
•
•
This section contains the following topics:
•
•
•
•
•
Note
The term Cisco ATA is used throughout this manual to refer to both the Cisco ATA 186 and the
Cisco ATA 188, unless differences between the Cisco ATA 186 and Cisco ATA 188 are explicitly stated.

Safety Recommendations

To ensure general safety, follow these guidelines:
•
•
•
•
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Read the installation instructions before you connect the system to its power source.
Warning
OL-4804-01
Planned the network and Cisco ATA configuration.
Installed the Ethernet connection.
Installed and configured the other network devices.
Safety Recommendations, page 2-1
What the Cisco ATA Package Includes, page 2-2
What You Need, page 2-2
Installation Procedure, page 2-3
Power-Down Procedure, page 2-5
Do not get this product wet or pour liquids into this device.
Do not open or disassemble this product.
Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.
Use only the power supply that comes with the Cisco ATA.
Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide for H.323 (version 3.0)
C H A P T E R
2
2-1

Advertisement

loading

Related Manuals for Cisco ATA 186

Summary of Contents for Cisco ATA 186

  • Page 1: Safety Recommendations

    Power-Down Procedure, page 2-5 Note The term Cisco ATA is used throughout this manual to refer to both the Cisco ATA 186 and the Cisco ATA 188, unless differences between the Cisco ATA 186 and Cisco ATA 188 are explicitly stated.

  • Page 2: What The Cisco Ata Package Includes

    5V power adaptor • Power cord • The Cisco ATA is intended for use only with the 5V DC power adaptor that comes with the unit. Note What You Need You also need the following items: Category-3 10BASE-T or 100BASE-T or better Ethernet cable. One cable is needed for each •...

  • Page 3: Installation Procedure

    PHONE 1 PHONE 2 LINK 10/100 PC 10/100 UPLINK LINK Power outlet IP network Analog telephones (or fax) 5V power adaptor Power cord Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide for H.323 (version 3.0) OL-4804-01...
  • Page 4 Place the Cisco ATA near an electrical power outlet. Step 2 Connect one end of a telephone line cord to the Phone 1 input on the rear panel of the Cisco ATA. Connect the other end to an analog telephone set.

  • Page 5: Power-Down Procedure

    “Hardware Overview” section on page 1-5. Power-Down Procedure Caution If you need to power down Cisco ATA 186 or Cisco 188 at any time, use the following power-down procedure to prevent damage to the unit. Procedure Unplug the RJ45 Ethernet cable Step 1 Wait for 20 seconds.
  • Page 6 Chapter 2 Installing the Cisco ATA Power-Down Procedure Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide for H.323 (version 3.0) OL-4804-01...

This manual is also suitable for:

Ata 188